OEM Delta Angle Grinder Parts & Accessories

Switch W/ Key

$41.51

Fix Number: FIX10325609
Manufacturer Part Number: 489105-00

This Switch is an OEM approved replacement part for various tools and models manufactured by Delta, Black and Decker, and Porter Cable. For full compatibility, please see the "Model Cross Reference List" below. This Switch has four terminals, a removable safety key, and a compact design for easy installation. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in power tools. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Switch is sold individually, and may also be referred to as a Rocker Switch.

Installation Instructions

keith from EMPORIA, KS

Power switch would not turn saw off

unplugged power cord.
removed the nut holding the power switch assembly on the saw.
removed 3 screws from the back cover.
removed the 2 white wires and 2 black wires from the switch terminal post. pay attention to wire color on each post.
removed old switch from the bracket by squeezing the sides of the old switch to remove the switch from the bracket.
inserted the new switch in place in the opening.
re attached the wires to the spade terminal on the switch using the 4 terminals. black on the 2 posts top and bottom on one side and the other side white on the top and bottom.
re attach the switch assembly to the table saw
test operation Read more...

Watch the install video

Ball Bearing (6001DW)

$12.91

★★★★★

1 Review

Fix Number: FIX10169632
Manufacturer Part Number: 330003-64

This is a ball bearing for your power tools. It is used in a variety of machines for rotary motion. The bearings support your tools by lowering the friction, which allows easy rotation of moving parts. Depending on how often you use your tool the bearings are a commonly replaced part. This is because they will experience most of the pressure, heat, and vibrations.

Installation Instructions

Michael from NEW BERLIN, WI

Bad bearing on brush end of Bucksaw motor

remove the brush cover on the end oppisite blade, unplug brush and remove bronze brusholder, if not replacing brushes , mark them for left and right. In my case the bearing had seized to the armature shaft much tighter than its normal shrink fit, so a bearing puller was needed, once the bearing is off, clean up shaft , heat bearing to about 200 deg F and blast end of shaft with cyrofreeze -60 F quickly drop bearing onto shaft and with very little effort it should slide on and bottom out on shaft. work quickly the shrink fit only lasts a few seconds. the trick is to heat bearing but not get it too warm and distort the plastic bearing cover. reinstall brush cap and old or new brushes. these old bucksaws are great for siding jobs , problem is only thing still available is the bearings and brushes. I think this saw is 35-40 years old , maybe I can get another 10 years out of it and by then I will be too old to lift it. Read more...

Arbor Nut (Left Hand Thread)

$31.14

Fix Number: FIX10327830
Manufacturer Part Number: 902012009848S

This arbor nut fits a variety of lawn and gardening tools. It is a left handed thread, which means if spin it the opposite way of a regular nut, which helps keep the nut secure when operating. To find the location of the nut inside the tool during installation, refer to the diagram provided by the manufacturer.

Blade Nut (Right Hand Thread)

$16.61

Fix Number: FIX10327835
Manufacturer Part Number: 902012012571S

Key

$10.37

Fix Number: FIX10318424
Manufacturer Part Number: 1343758

This safety key fits multiple hardware tools and is inserted into the switch to make it possible for your machine to turn on and operate. Tip: you can remove the key to prevent unauthorized use of the machine. For installation instructions refer to the diagram provided by the manufacturer.

Washer

$5.19

Fix Number: FIX10176170
Manufacturer Part Number: 5140010-69

This is a washer for your power tools. It is made of steel, and is sold individually. The washer is needed to evenly divide pressure and weight between two connected parts. It has various applications, depending on your equipment.

Right Fixed Work Rest

$12.45

★★★★★

1 Review

Fix Number: FIX10332165
Manufacturer Part Number: DPEC002843

Eyeshield

$12.45

Fix Number: FIX10332158
Manufacturer Part Number: DPEC002836

Nut,Hex

$4.99

Fix Number: FIX10169670
Manufacturer Part Number: 330015-03

This hex nut with internal threads, screws to the shank of a bolt or a hex cap screw in a variety of lawn and gardening tools. It can have multiple applications depending on the tool you are using. To replace, you will need a wrench to loosen and tighten the nut. For detailed installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug tool from power source before beginning this repair project.