Angle Grinder Parts

Carbon Brush Set

$19.19

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Carbon Brush Set

$24.97

Fix Number: FIX10156653
Manufacturer Part Number: CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

BRUSH SET

$24.68

Fix Number: FIX19500958
Manufacturer Part Number: 1607000V61

This carbon brush set replaces worn brushes in select power grinders to restore steady motor performance and prevent issues like power loss, excess sparking, or intermittent operation. The set includes the brushes, springs, and holders needed for a proper fit, helping the tool run smoothly and reliably again. Designed for specific grinder models, it offers a straightforward repair solution when the motor begins to hesitate or fail to start. Checking your tool’s model number is recommended to ensure the correct match.

Grinder Cordset

$29.55

★★★★★

1 Review

Fix Number: FIX11929697
Manufacturer Part Number: N353819

This is an original replacement part manufactured for use with DeWalt angle grinders. This two wire cord had a rubberized jacket, and the wires have crimped terminals to make installation easier. The cordset is available individually.

Watch the install video

Hex Hole Flange

$9.68

Fix Number: FIX10188627
Manufacturer Part Number: N134467

This is an Original Manufacturer Sourced replacement part used on Dewalt Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Hex Hole Flange Nut is to hold the Grinding Wheel to the Spindle Shaft. You would need Hex Wrench to secure this part.

Watch the install video

Clamp Washer

$6.51

Fix Number: FIX10188483
Manufacturer Part Number: N115381

This is an OEM metal clamp washer for angle grinders. It is located on the spindle shaft and gives support to the grinding wheel. Most of our customers have found this repair very quick and easy. You will need a hex wrench to complete the installation.

Watch the install video

Flange Nut

$7.98

★★★★★

2 Reviews

Fix Number: FIX10131039
Manufacturer Part Number: 44-40-0035

This is an authentic flange nut for multiple grinder models. The flange nut fits onto the spindle, followed by the grinding wheel. The flange is secured in place using a spanner wrench, which fits neatly into the holes of the flange nut. It measures approximately 5/8-inches and is sold individually.

Watch the install video

Carbon Brush

$6.51

★★★★★

1 Review

Fix Number: FIX10188358
Manufacturer Part Number: N097696

Genuine Dewalt replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Watch the install video

Power Cord

$27.56

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Carbon Brush

$9.60

Fix Number: FIX17062120
Manufacturer Part Number: NA121629

Genuine Dewalt replacement part used on Small Angle Grinder. This brush has a lead wire attached and it is Sold Individually. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Popular Angle Grinder Parts

Installation Instructions

Angle Grinder Brands

Related Angle Grinder Parts

Popular Angle Grinder Models

Angle Grinder Parts

Start With Your Model Number

Popular Angle Grinder Parts

Installation Instructions

Angle Grinder Brands

Related Angle Grinder Parts

Popular Angle Grinder Models