Angle Grinder Seals and Gaskets

Popular Angle Grinder Seals and Gaskets

O-ring
$6.51
In Stock
Fix Number
FIX10182951
Manufacturer Part Number
633044-00
This is an authentic manufacturer sourced replacement part designed for use with Dewalt grinders. It helps to provide an air tight seal for the gearbox. It is made out of rubber material and it is sold individually. To complete this repair you will need a spanner wrench.
O-ring
$6.51
In Stock
Fix Number
FIX11929698
Manufacturer Part Number
N355619
This part is sold individually. The o-ring goes on the guard and is made of rubber. A set of pliers and a screwdriver might be needed during the installation process. It may become broken and will need to be replaced. This part is an OEM from DeWALT for use in grinders.
O-ring
$6.51
In Stock
Fix Number
FIX10142022
Manufacturer Part Number
213960-9
O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> • O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> • O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> • O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> • O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.
O-ring
$6.51
In Stock
Fix Number
FIX10182950
Manufacturer Part Number
633043-00
O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity.<u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.
O-ring
$6.51
In Stock
Fix Number
FIX10126900
Manufacturer Part Number
34-40-0450
This is a genuine manufacturer-sourced replacement o-ring which is specially designed for use with Milwaukee angle grinders. It is utilized to provide an air-tight seal between connected pieces, make sure to check appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable rubber material and is sold individually.
O-ring
$6.51
On Order
Fix Number
FIX11929646
Manufacturer Part Number
N263699
This authentic manufacturer-supplied washer is specially designed for use with DeWALT angle grinders. It is a special hardware that helps to provide a tight seal between connected components. This is an identical replacement for a missing or a damaged O-ring that was installed on a new unit. One durable rubber part is included. Refer to the appropriate diagrams for your model to ensure the proper replacement procedure. A screwdriver will be needed to take apart and reassemble the housing to perform this repair.
Seal
$9.84
In Stock
Fix Number
FIX10336573
Manufacturer Part Number
01464
This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.
O-Ring
$6.51
In Stock
Fix Number
FIX10188533
Manufacturer Part Number
N119639
O-ring
$6.51
Special Order
Fix Number
FIX10126936
Manufacturer Part Number
34-40-1375
This is a genuine manufacturer-sourced replacement o-ring which is specially designed for use with Milwaukee power tools. It is generally utilized to provide an air-tight seal between connected pieces, make sure to check appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable rubber material and is sold individually.
O-ring
$6.51
In Stock
Fix Number
FIX10127036
Manufacturer Part Number
34-40-4300
Included in part number 14-30-0302

Angle Grinder Seal or Gasket Brands