OEM Milwaukee Angle Grinder Parts & Accessories

Carbon Brush Assembly

$13.75

Fix Number: FIX10122265
Manufacturer Part Number: 22-18-2240

This is an authentic set of two carbon brushes, including the brush, holder, and spring. This is one of the most regularly replaced parts in a power tool due to the constant friction created and leading to wear. If the motor is not functioning properly, a worn brush is usually the cause. We suggest also checking the armature for damage at the same time as this may suggest a more serious problem with the motor.

Carbon Brush Set

$13.15

Fix Number: FIX10122266
Manufacturer Part Number: 22-18-2250

This is a set of two authentic carbon brushes with wire leads, springs, and brush holders. Your equipment uses two carbon brushes to conduct electricity to the armature through the commutator. This is a very common repair due to the constant rubbing of the carbon brushes against the turning commutator. It may become obvious that a repair is needed if sparks are excessive, however it is important to also check the armature for damage at the same time. To access these brushes, you will begin by removing the guard, the side handle, and the rear housing. The brushes are likely secured with one screw, which will need to be removed. Remove the brushes away from the housing and disengage the wire lead. These instructions may vary depending on your model but should give you a general idea of the simplicity of the repair.

4.5

$27.45

Fix Number: FIX17081481
Manufacturer Part Number: 43-54-1200

Inner Disc Flange

$8.89

Fix Number: FIX10130006
Manufacturer Part Number: 43-34-0935

This is an OEM inner disc flange, which is found on the spindle of a handheld grinder. Its function is to secure the grinding wheel to the spindle and providing support to the wheel, along with the flange nut (sold separately). It has a 5/8-inch non-threaded hole and a recess in it that engages with the spindle, and a 7/8-inch hub to accept a standard grinding wheel. This part is prone to wear and tear, which can lead to an unbalanced wheel. This is a simple repair that should only take a few minutes and should only require a wrench.

Paddle Trigger Assy

$7.65

Fix Number: FIX17077356
Manufacturer Part Number: 31-92-1060

Paddle Trigger Assembly

$8.19

Fix Number: FIX17017004
Manufacturer Part Number: 31-92-0210

This paddle trigger assembly is supplied by the original manufacturer for use in angle grinders. It allows the user to control the speed and operation of the equipment. The paddle is 5 inches long and 1.25 inches wide. It includes a switch that activates the motor and allows the grinding wheel to spin and a safety lock to prevent accidental starting. If the grinder does not start when you press the switch, stops unexpectedly, has inconsistent speeds, and makes unusual noises when you attempt to use it, the assembly will need to be replaced. Begin by ensuring the equipment is switched off. Remove the fasteners that hold the assembly in place and detach it from the equipment. Position the new assembly on the mounting surface and secure it in place with the appropriate fastener

Carbon Brush Assembly

$6.51

Fix Number: FIX10122351
Manufacturer Part Number: 22-22-0085

This is a carbon brush for an angle grinder, sold individually. Carbon brushes are commonly replaced because of the constant friction they endure. If the motor of your equipment is underperforming, a worn brush is the likely reason. Changing the carbon brush is part of your tools regular maintenance and is a very straight-forward repair. This carbon brush assembly is sourced right from the original manufacturer, ensuring the best possible quality.

Watch the install video

Cord Protector

$6.51

Fix Number: FIX10131782
Manufacturer Part Number: 44-76-0210

This cord protector is created to slide onto your cord and fit tightly at the end to protect the base of the cord from getting damaged. If the wires are exposed it can a be a safety hazard, so make sure to replace your cord protector if damaged. Refer to the manual provided by the manufacturer for further installation instructions.

Carbon Brush

$7.72

Fix Number: FIX10122198
Manufacturer Part Number: 22-18-0710

This carbon brush lead or also known as a carbon motor brush fits the following tools: angle grinders, nibbler and shears, sander polishers, and jig saws. This includes the brush and a wire lead attached. This is one of the most commonly replaced power tool components because the carbon brushes easily wear off with friction and use. If your brush is worn out it can cause intermittent motor function, reduction in electric braking, and in motor power. If you notice burns and cracks on the wire lead, then it is best to replace this part. Tip: when replacing your carbon brush, make sure to inspect your armature for damage as well, in case there are larger motor problems.

Watch the install video

Disk Flange

$6.55

★★★★★

1 Review

Fix Number: FIX10129924
Manufacturer Part Number: 43-34-0036

This part includes one disk flange for a grinder. This disk flange is an OEM quality part, ensuring the perfect fit. The disc flange works with the nut to secure the grinding disk to your grinder. It is common for the hub to wear, which can lead to a wobbly grinding wheel. For this quick and easy repair, you will need a wrench to remove the nut and a screwdriver to help pry off the old disk flange.

Milwaukee Angle Grinder Parts

Popular Milwaukee Angle Grinder Parts

Milwaukee Angle Grinder Appliance Types

Related Milwaukee Angle Grinder Parts

Popular Milwaukee Angle Grinder Models

Milwaukee Angle Grinder Parts

Start With Your Model Number

Popular Milwaukee Angle Grinder Parts

Milwaukee Angle Grinder Appliance Types

Related Milwaukee Angle Grinder Parts

Popular Milwaukee Angle Grinder Models