DeWALT Angle Grinder Parts

Start With Your Model Number

Need help finding your model number?

Find Parts Fast

Guaranteed Fit

Repair Videos

Popular DeWALT Angle Grinder Parts

Carbon Brush

$9.60

In Stock

Add to cart

Fix Number

FIX17062120

Manufacturer Part Number

NA121629

Genuine Dewalt replacement part used on Small Angle Grinder. This brush has a lead wire attached and it is Sold Individually. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Watch the install video

Hex Hole Flange

$9.68

In Stock

Add to cart

Fix Number

FIX10188627

Manufacturer Part Number

N134467

This is an Original Manufacturer Sourced replacement part used on Dewalt Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Hex Hole Flange Nut is to hold the Grinding Wheel to the Spindle Shaft. You would need Hex Wrench to secure this part.

Watch the install video

Carbon Brush

$6.51

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX10188358

Manufacturer Part Number

N097696

Genuine Dewalt replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Watch the install video

Clamp Washer

$6.51

In Stock

Add to cart

Fix Number

FIX10188483

Manufacturer Part Number

N115381

This is an OEM metal clamp washer for angle grinders. It is located on the spindle shaft and gives support to the grinding wheel. Most of our customers have found this repair very quick and easy. You will need a hex wrench to complete the installation.

Watch the install video

Power Cord

$27.56

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Brush

$13.07

In Stock

Add to cart

★★★★★

★★★★★

2 Reviews

Fix Number

FIX10183735

Manufacturer Part Number

650916-01

Sold Individually This motor brush is for angle grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the angle grinder before installing this part. Wear work gloves to protect your hands.

Installation Instructions

Pam from BENBROOK, TX

Worn brush

Honestly I Utubed it, cause it was the first time I've done it and wanted to make sure I did it right, super easy. Read more...

Guard

$16.84

In Stock

Add to cart

Fix Number

FIX11929669

Manufacturer Part Number

N306360

This is a black metal guard for smaller angle grinders and is sold individually. This part is sourced directly from the manufacturer, ensuring it is an exact replacement for your worn or damaged part. The function of the guard is to direct dust and debris away from the direction of the operator, while the tool is being used. It also provides protection from the grinding disk. Never use your tool if this is missing or damaged, as it is important for safe operation.

Grinder Cordset

$29.55

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX11929697

Manufacturer Part Number

N353819

This is an original replacement part manufactured for use with DeWalt angle grinders. This two wire cord had a rubberized jacket, and the wires have crimped terminals to make installation easier. The cordset is available individually.

Carbon Brush With Wire Lead

$17.15

In Stock

Add to cart

Fix Number

FIX10171526

Manufacturer Part Number

392574-01

Genuine DeWalt replacement part Includes 1 Carbon Brush with wire lead attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Cord Protector

$6.51

In Stock

Add to cart

Fix Number

FIX17061542

Manufacturer Part Number

N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

DeWALT Angle Grinder Appliance Types

• Angle Grinder Parts
• DeWALT Parts

Related DeWALT Angle Grinder Parts

• DeWALT Angle Grinder Brackets and Flanges
• DeWALT Angle Grinder Knobs

Popular DeWALT Angle Grinder Models

• DWE402 4-1/2" Small Angle Grinder
• DWE402 (Type 4) 4-1/2in 11a Ang Grnd
• DWE402 (Type 1) 4-1/2in 11a Ang Grnd
• DWE402 (Type 2) 4-1/2in 11a Ang Grnd
• DWE402 (Type 3) 4-1/2in 11a Ang Grnd
• DWE402 (Type 15) 4-1/2in 11a Ang Grnd
• DWE4011 4.5" Small Angle Grinder
• D28402 (Type 1) Small Angle Grinder
• D28402 (Type 2) 4 1/2 Small Angle Grinder
• DWE43116 (Type 15) 4-1/2-5/6i 13a 9k Tr
• DWE43116 (Type 2) 4-1/2-5/6i 13a 9k Tr
• DW840 (Type 3) 7 Angle Grinder
• DW840 (Type 1) 7 Angle Grinder
• DW840 (Type 2) 7 Angle Grinder
• DW840 (Type 15) Angle Grinder
• DW840 (Type 4) 7 Angle Grinder
• DW840 (Type 5) 7 Angle Grinder
• DWE402N (1) 4-1/2" Angle Grinder
• DWE402N (2) 4-1/2" Angle Grinder
• DWE402N (4) 4-1/2" Angle Grinder