DeWALT Parts

Fix Number

FIX17062120

Manufacturer Part Number

NA121629

Genuine Dewalt replacement part used on Small Angle Grinder. This brush has a lead wire attached and it is Sold Individually. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX12417689

Manufacturer Part Number

180450-S

This is a genuine head valve for nailers and staplers. The head valve is responsible for controlling the flow of air to the cylinder. When the trigger is pulled, it creates an imbalance of pressure, which opens the head valve and fires the piston. The head valve is prone to wear over time, so it is important to inspect it often. The seals on the head valve or the body itself can begin to harden and eventually crack, and this results in air leaking from the gun exhaust. For this repair you will need an Allen wrench adjustable wrench and a screwdriver. This plastic head valve is sold individually.

Fix Number

FIX10177102

Manufacturer Part Number

5140033-19

This part includes one carbon brush with a wire lead and brush spring attached. A strong indication that the carbon brush might need to be replaced is if your equipment will not turn on or there are excessive sparks present. This is a common wear part that will require replacement from time to time. It is also a good idea to inspect the armature at the same time, especially in the case of excessive sparks.

Fix Number

FIX16687899

Manufacturer Part Number

N558583

This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Fix Number

FIX12522639

Manufacturer Part Number

N292059

This is a brush box assembly designed for various sander models. Brush boxes are essential components that house carbon brushes responsible for transferring electricity from the motor to the sanding pad. When the carbon brush assembly wears out, it can no longer efficiently transfer electricity, causing the sander to stop working. This brush box assembly includes the carbon brush, its housing, and the necessary wiring. Replacing the brush box assembly is a straightforward process, requiring only a screwdriver and a set of pliers. Begin by disconnecting your sander from its power source, whether it is a battery or a wall outlet. Next, remove the screws securing the main housing of the sander and locate the brushes inside. Use a set of pliers to disconnect the wire from the old brush and a flat-head screwdriver to lift the old brush out of its slot. Insert the new brush box assembly into the slot and connect its wires. Finally, reattach the sander outer housing and secure it with the screws.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX12417689

Manufacturer Part Number

180450-S

This is a manufacturer-approved replacement head valve and is sold independently. It controls the amount of air that enters the cylinder when the trigger is initiated. This action creates an imbalance in pressure between the cylinder and the air reservoir, allowing the head valve to open, firing the piston. The head valve can harden and crack and the valve body itself can break too. This will usually become obvious because air will leak from the gun exhaust. To access this part for the repair, you will need to remove the top cap from the nail gun.

Fix Number

FIX12508695

Manufacturer Part Number

N413423

This is the housing assembly for an impact driver. This plastic casing includes the right and left side, is yellow and black in color, and has the DeWalt logo on the side. The housing is what protects in inner components of the tool. If the housing has become worn, cracked, or damaged, this is the OEM replacement part needed to fix it. For this simple repair, you will need to remove the screws holding the old housing assembly in place (screws sold separately) and remove everything out of the old case and transfer them to the new case.

Fix Number

FIX10188627

Manufacturer Part Number

N134467

This is an Original Manufacturer Sourced replacement part used on Dewalt Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Hex Hole Flange Nut is to hold the Grinding Wheel to the Spindle Shaft. You would need Hex Wrench to secure this part.

★★★★★

★★★★★

1 Review

Fix Number

FIX10188358

Manufacturer Part Number

N097696

Genuine Dewalt replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10170261

Manufacturer Part Number

381028-08

This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.