OEM DeWALT Table Saw Parts & Accessories

Power Cord

$35.31

Fix Number: FIX10169913
Manufacturer Part Number: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Kerf Plate

$25.59

Fix Number: FIX16687705
Manufacturer Part Number: N544383

This replacement part is specially designed for Dewalt compound miter saws. It is supplied directly from original equipment manufacturer. Kerf boards, also known as kerf plates are used to prevent excessive splintering. This results in better and cleaner cuts. This part is made out of yellow plastic and it is sold individually. Screws that attach this kerf board are sold separately.

Watch the install video

Brush

$18.58

Fix Number: FIX10170261
Manufacturer Part Number: 381028-08

This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.

Handwheel

$21.98

Fix Number: FIX10178360
Manufacturer Part Number: 5140117-77

This is an OEM handwheel for a table saw, which allows the user to adjust the blade height. This handwheel is made from black plastic (bevel handle is sold as a separate part) and attaches to a metal cross pin on the spindle. The plastic will wear over time, causing it to slip and not adjust the blade. This is a simple repair that should only take a few minutes. Start by removing the nut, pull the handle away from the saw (being careful not to misplace the washer), and secure the new assembly by aligning the notches with the roll pin, and secure the new handwheel with the nut.

Brush and Spring

$12.60

★★★★★

1 Review

Fix Number: FIX10166057
Manufacturer Part Number: 145323-06

This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.

Fixes these symptoms

Won't turn on
See more...

Brush, 105s/sus304

$9.51

Fix Number: FIX16689135
Manufacturer Part Number: N713244

Wear Plate

$29.83

Fix Number: FIX10181974
Manufacturer Part Number: 618192-00

A miter table that sticks, scrapes, or turns roughly may have a worn wear plate. This thin plate sits between moving parts of the saw base to reduce friction and help the table turn smoothly for angle cuts. Before replacing it, remove packed sawdust and inspect the base, detent plate, lock, and mounting screws for damage. Confirm fit with the complete saw model and type number. Unplug the saw, lower and lock the cutting head, and remove the blade if the manual requires it. After assembly, check table movement and angle accuracy before cutting.

Watch the install video

Clamp Knob Assembly

$22.13

Fix Number: FIX10168807
Manufacturer Part Number: 286303-00

This is a single OEM clamp knob assembly for a saw. The clamp knob is what secures the blade in the saw blade clamp. This assembly has a wingnut cast onto a threaded metal stud. With use, the clamping surface will deteriorate, which causes the blade to slip. The threads on the metal stud can also start to strip. For this quick and easy repair, you will need to disconnect the blade, and then unscrew and remove the clamp knob from the blade chuck. To install your new part, fasten the clamp knob into the blade chuck and reassemble the blade.

Carbon Brush

$6.20

Fix Number: FIX16687899
Manufacturer Part Number: N558583

This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Watch the install video

Brush

$7.89

Fix Number: FIX10177102
Manufacturer Part Number: 5140033-19

This part includes one carbon brush with a wire lead and brush spring attached. A strong indication that the carbon brush might need to be replaced is if your equipment will not turn on or there are excessive sparks present. This is a common wear part that will require replacement from time to time. It is also a good idea to inspect the armature at the same time, especially in the case of excessive sparks.

DeWALT Table Saw Parts

Popular DeWALT Table Saw Parts

DeWALT Table Saw Appliance Types

Related DeWALT Table Saw Parts

Popular DeWALT Table Saw Models

DeWALT Table Saw Parts

Start With Your Model Number

Popular DeWALT Table Saw Parts

DeWALT Table Saw Appliance Types

Related DeWALT Table Saw Parts

Popular DeWALT Table Saw Models