OEM DeWALT Chop Saw Parts & Accessories

Carbon Brush With Wire Lead

$17.15

Fix Number: FIX10171526
Manufacturer Part Number: 392574-01

Genuine DeWalt replacement part Includes 1 Carbon Brush with wire lead attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Watch the install video

Brush Holder

$6.51

Fix Number: FIX10182308
Manufacturer Part Number: 622440-00

This is a genuine OEM approved replacement part designed for use with chop saws. This item holds carbon brush against the armature. It is made out of plastic with metal and it is sold individually. Please note carbon brushes are sold separately. To replace this assembly you would need a screwdriver and pliers. • First remove screws holding the cover together • Carefully remove two halves of the housing to gain access to armature and brush holder • Remove the screws holding brush holder to the trigger • Remove the armature assembly and the brush holder • Install the new brush holder, brushes and the armature • Reassemble and test your tool

Watch the install video

Ball Bearing

$8.25

Fix Number: FIX10180911
Manufacturer Part Number: 605040-27

This part includes one OEM ball bearing. This ball bearing is sealed on both sides. They are designed to minimize friction between moving parts and evenly distribute weight. Bearings are a general wear part that require regular maintenance to keep your equipment running smoothly and efficiently.

Ball Bearing

$7.79

Fix Number: FIX10180919
Manufacturer Part Number: 605040-66

This bearing is authentic OEM. It is used in some models of DeWALT band saws. Ball bearings hold and stabilize rotating parts to ensure low friction movement. With regular use, bearings should be replaced often. Sold separately.

Wrench

$19.40

Fix Number: FIX10172231
Manufacturer Part Number: 401680-00

This wrench is an OEM direct from Craftsman for angle grinders. This part helps the motor shaft stay in place when the user pulls out or replaces the grinder disc. It is recommended to review your models diagram to verify the parts compatibility. This part is made of metal and sold individually.

Shoulder Bolt

$6.51

Fix Number: FIX10183732
Manufacturer Part Number: 650736-00

This is a Genuine Manufacturer Approved replacement part used on certain Dewalt Band Saws. The purpose of this Bolt is to attach Ball Bearings to Bearing Block. This item is made out of Metal and is Sold Individually.

Watch the install video

Retaining Ring

$6.51

Fix Number: FIX10166028
Manufacturer Part Number: 144803-00

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

Watch the install video

Power Cord

$40.44

Fix Number: FIX10169913
Manufacturer Part Number: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Ball Bearing

$35.64

Fix Number: FIX10166095
Manufacturer Part Number: 146555-01

Genuine Manufacturer Sourced replacement part used on a variety of equipment. This part is made out of Metal and is Sold Individually. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. Included in part number 395843-00

Carbon Brush

$6.20

Fix Number: FIX16687899
Manufacturer Part Number: N558583

This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

DeWALT Chop Saw Parts

Popular DeWALT Chop Saw Parts

DeWALT Chop Saw Appliance Types

Related DeWALT Chop Saw Parts

Popular DeWALT Chop Saw Models

DeWALT Chop Saw Parts

Start With Your Model Number

Popular DeWALT Chop Saw Parts

DeWALT Chop Saw Appliance Types

Related DeWALT Chop Saw Parts

Popular DeWALT Chop Saw Models