OEM DeWALT Hammer Drill Parts & Accessories

Plain Washer

$6.51

Fix Number: FIX11929226
Manufacturer Part Number: N016823

This is a genuine OEM plain washer and is part of your impact driver chuck assembly. The washer fits over the compression spring and provides a flat surface for the hog ring to sit against. This part usually needs to be replaced because it has been lost during the disassembly of the chuck. To begin this repair, remove the hog ring from the chuck, being mindful not to misplace the spring. Now you can place the compression spring in place and the new washer over top and reinstall the hog ring. Use a pair of needle nose pliers to push the compression spring as you install the hog ring over the spindle.

Brush Kit ( Includes Both Brus

$35.77

Fix Number: FIX10165412
Manufacturer Part Number: 1005550-03

This carbon brush kit is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Dewalt demolition hammers. This set includes (2) carbon brushes with lead wires attached. It is advised to replace both brushes at the same time. You will need a screwdriver to complete this repair.

Bearing

$6.51

Fix Number: FIX10188435
Manufacturer Part Number: N110359

This authentic ball bearing is sold individually. It can be used in a variety of differently model types, such as miter saws, circular saws, table saws, and angle grinders. This ball bearing is sealed on both sides. Its job is to minimize friction between rotating parts. The armature rotates at a very fast rate, so after years of use, it is normal for the bearings to wear.

Watch the install video

Belt Hook

$6.51

Fix Number: FIX10189049
Manufacturer Part Number: N268241

This OEM belt hook makes it possible for drills and drill drivers to attach to a regular belt or tool belt. It attaches to the bottom of the handle assembly and makes it convenient to access your tool when it is not in use. This part includes the belt hook and screw needed to attach it.

Watch the install video

Brush Box

$13.49

★★★★★

1 Review

Fix Number: FIX10180814
Manufacturer Part Number: 603754-01

This brush box holds the carbon brush firmly against the motor so the tool can run as it should, worn parts may cause low power, sudden stops, heavy sparking, or a burning smell, one brush, one spring, and one metal holder are included, this item is sold on its own, use the model number and parts diagram to confirm fit and quantity

Keyless Chuck

$32.33

Fix Number: FIX16686663
Manufacturer Part Number: N472497

This genuine OEM sourced drill chuck is designed for use with Dewalt drills/drivers. Its purpose is to secure drill bits. This keyless chuck allows for easy bit exchange without any tools. Please note this chuck is sold individually. The screw used to secure chuck is sold separately. To complete this job you would need a hex key/allen wrench. • Remove chuck screw • Take out old chuck • Secure new chuck • Install chuck screw and test the unit

Watch the install video

Retaining Ring

$6.51

Fix Number: FIX10166028
Manufacturer Part Number: 144803-00

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

O Ring

$6.51

Fix Number: FIX10165223
Manufacturer Part Number: 049787-00

It is a high-quality component which is supplied by the original equipment manufacturer for use with Dewalt and Black and Decker power tools. This replacement o-ring has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. It is made of durable rubber material and it is sold individually.

Watch the install video

Carbon Brush And Holder Set

$21.17

★★★★★

1 Review

Fix Number: FIX10187386
Manufacturer Part Number: N031214

This part contains two carbon brushes and holder sets. Carbon brushes are a routine maintenance task, as they are prone to wear due friction. Worn brushes are the most common reason for a motor that is not running properly or at all. In general, this is a pretty easy repair, but keep in mind that instructions can vary slightly depending on the model. To access the brushes, you will need to remove the housing of the tool and the brushes will be located inside the holders close to the motor.

Miter Saw Ball Bearing

$16.20

★★★★★

1 Review

Fix Number: FIX10188573
Manufacturer Part Number: N127530

This Ball Bearing is sealed on both sides. It is a genuine replacement part and is sold individually. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Fixes these symptoms

Grinding or squealing sound
See more...

DeWALT Hammer Drill Parts

Popular DeWALT Hammer Drill Parts

DeWALT Hammer Drill Appliance Types

Related DeWALT Hammer Drill Parts

Popular DeWALT Hammer Drill Models

DeWALT Hammer Drill Parts

Start With Your Model Number

Popular DeWALT Hammer Drill Parts

DeWALT Hammer Drill Appliance Types

Related DeWALT Hammer Drill Parts

Popular DeWALT Hammer Drill Models