DeWALT Scroll Saw Parts

Fix Number

FIX10168800

Manufacturer Part Number

286294-00

The short sleeve helps to distribute pressure evenly between connected components. Over time it will wear out, get damaged or lost eventually requiring a replacement. This authentic manufacturer-sourced part is specially designed for use with DeWALT and Delta scroll saws. Check the diagrams for your model for the exact location and the correct application of this hardware. Keep in mind this high-quality short sleeve is made of durable metal and is sold individually.

Fix Number

FIX10177981

Manufacturer Part Number

5140092-86

This is an OEM replacement part used in Delta and DeWALT scroll saws. It is an on/off switch and is sold individually, separate from the speed control knob. It is plastic with metal terminals. Over time, mechanical parts such as these wear down and must be replaced. To complete this repair you will need a hex key/allen wrench. • Remove old switch by pressing tabs • Disconnect wires • Attach wires to the new switch • Reassemble and test the tool

Fix Number

FIX10178031

Manufacturer Part Number

5140099-98

Genuine Dewalt replacement part, this item is sold individually. This is a part of the blade holding assembly on the Scroll Saws listed below.>br>Along with the other parts shown in the parts diagram this will clamp the scroll saw blade and hold it in place.

Fix Number

FIX10168799

Manufacturer Part Number

286292-00

This part is guaranteed OEM, made to fit the DeWALT and Delta scroll saws listed below. This hold down foot is attached to the top mount via the black bar. Note that mounting/adjustment screw is sold separately. This foot is sold individually. Associated parts: • Top Mount, part # 286277-00 • Bar, part # 286291-00 • Screw, part # 286316-00

Fix Number

FIX10168837

Manufacturer Part Number

286344-00

This fuse is a high quality part sourced from the original manufacturer for DeWalt and Delta scroll saws. The fuse is a safety feature to prevent an electric surge from overloading the motor. Once the fuse is tripped it will burn itself out, and will need to be replaced. This part is sold individually, keep in mind the fuse cap is sold separately.

Fix Number

FIX10168796

Manufacturer Part Number

286289-00

This is an authentic replacement part, sourced from the original manufacturer for use with scroll saws. The special rubber bellow is used to push air through the air pump and through the air nozzle. This bellow is available as an individual replacement part, please see model diagram for associative parts.

Fix Number

FIX11927427

Manufacturer Part Number

5140163-11

It is a genuine item that is supplied directly from the original equipment manufacturer for use with DeWALT and Delta scroll saws. These are the parts utilized to secure the fuse which is sold separately. One durable plastic cap and a holder are included. Make sure to check the owner's manual for your model to ensure the proper repair procedure. A screwdriver will be needed to take the housing apart to perform this repair.

Fix Number

FIX10168844

Manufacturer Part Number

286429-00

This is a genuine DeWALT replacement part sourced directly from the manufacturer. The washer is commonly found in DeWALT scroll saws. This part is made of metal and is used to provide space and tension to the pivot rod. Please be aware that there are different washers used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You may require a screwdriver to replace this part. This item is sold individually.

Fix Number

FIX10168798

Manufacturer Part Number

286291-00

This is a genuine OEM sourced replacement part that is intended to be used with scroll saws from DeWalt and Delta. The metal bar attaches to the top rocker mount and is used to support the foot that protects the blade. The bar will require a torx driver and hex driver to install, and the bar is priced as a single item.

Fix Number

FIX10168838

Manufacturer Part Number

286346-00

Genuine DeWalt replacement part Includes 1 Carbon Brush with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.