DeWALT Sander Polisher Parts

DeWALT Appliance Parts

Popular DeWALT Sander Polisher Parts

BRUSH & SPRING
$10.79
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12522806
Manufacturer Part Number
N031635
This part includes one carbon brush with a wire lead and brush spring attached. A poorly running motor is often due to worn brushes, which is why they are such a common repair in power tools. Due to the constant friction they are under, they will wear over time, and will need to be replaced. If upon inspection you notice the carbon brush is burnt or otherwise damaged, you will also want to check the condition of the armature, as this might suggest a larger problem with the motor.
Sander Carbon Brush Set
$11.51
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11929758
Manufacturer Part Number
N398321
This motor brush set is for power tools. The motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes. Unplug the power tool before installing this part.
Power Cord
$27.56
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10169875
Manufacturer Part Number
330072-98
This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI
Did not come with grinding disc guard
While unit was unplugged I screwed clamp of guard around grinder. Read more...
BRUSH
$12.35
In Stock
Fix Number
FIX12410247
Manufacturer Part Number
445861-25
(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.
STRAIN RELIEVER
$12.08
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12499955
Manufacturer Part Number
901266
This is a strain reliever for your power tools. It found at the meeting place between your cord, and the outer tool housing. The relief is an important part for your power tool because it protects your cord from tearing and breaking due to constant pressure. Keep your relief in good condition because it will extend the life of the cord, and the machine overall.

Installation Instructions

Jeff from WISC RAPIDS, WI
Strain reliever broken at base of saw. Core frayed.
1. Unplug saw. 2.Examine and determine which parts need to be removed to gain access to switch. 3.Remove screws one at a time and placed in dish keeping track of size and length of where removed from handle. 4. Slowly pull handle apart exposing switch and wires. 5. Remove screws holding black and white wires keeping track of which wire goes where. 6. Thread new power cord the same way the old one was positioned though the handle and reassemble. Read more...
On-off Switch
$6.51
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10166039
Manufacturer Part Number
144960-00
This part includes one on-off switch, also referred to as a rocker switch. This switch is an original manufacturer replacement part. The switch controls the flow of electricity to the motor, and when it wears it can make it impossible to start the power tool. Switches are a common replacement part for power tools, so it is something that should be inspected as part of your regular maintenance. This black switch has two terminals and a compact design for an uncomplicated installation process. To confirm that the switch is damaged, you can test it for continuity using a multimeter.
Carbon Brush With Spring
$11.90
In Stock
Fix Number
FIX10173724
Manufacturer Part Number
450374-12
This is a brush and spring for your power tools. This brush is sold individually, and two are needed for most power tools. We recommend replacing both brushes together for an even wear. When your brush wears down it will greatly affect your motor function by reducing the power and electric braking. When making this repair we recommend inspecting the armature for cracks or visible damage that would mean other motor problems. Carbon brushes are the most commonly replaced power tool part. This part is meant to wear out over time through the constant contact.
BRUSH CAP
$6.51
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12494900
Manufacturer Part Number
803483
This is a brush cap for your power tools. It holds the brush inside the tool. It has external threads that lead into the housing of the tool. When removing this part be gentle because too much pressure can make them crack. This part is made of plastic, and is sold individually. To remove the brush cap you should use a flat head screw driver.
Dust Bag Assembly
$12.14
In Stock
Fix Number
FIX12522964
Manufacturer Part Number
N273733
This authentic OEM dust bag assembly is sourced from the original manufacturer for use in sanders. It consists of a fabric bag and plastic cap measuring approximately 5.5 inches in length and 2.5 inches in diameter. The bag assembly collects the dust and debris that is produced during sanding allowing you to maintain a clean and safe working environment. Over time the bag may tear or wear down, leading to large amounts of dust escaping into the air, health hazards from dust inhalation, reduction in visibility, and a messy work area. Replacing the dust bag assembly is a simple repair that does not require the use of specialized tools. Simply detach the bag from the sander, remove any dust and debris on the mounting surface, and attach the new bag.
★★★★★
★★★★★
1 Review
Fix Number
FIX10166489
Manufacturer Part Number
151284-00SV
This is an OEM sander pad and backing plate for a sander. It is most commonly replaced due to sudden uneven sanding or difficulty keeping the sandpaper properly attached. This part includes a steel plate with a foam pad fixed to it. The foam pad gives grip for the sandpaper to adhere firmly within the clamps. This foam material is prone to deteriorate over time, causing irregular sanding. If the pad is so worn that the metal plate is making contact with the paper, the sander will start to jump around. This is a very quick and easy repair. Simply remove the four screws holding the old pad in place, line up the the holes of the pad with the holes in the plate, and tighten the four screws back up (screws sold separately).

DeWALT Sander Polisher Appliance Types

Related DeWALT Sander Polisher Parts

Popular DeWALT Sander Polisher Models