DeWALT Sander Polisher Power Cords

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Fix Number

FIX10169908

Manufacturer Part Number

330078-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 16 Gauge • 10 Feet Long

Fix Number

FIX10169655

Manufacturer Part Number

330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Fix Number

FIX10169907

Manufacturer Part Number

330077-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 8 Feet Long

Fix Number

FIX10169874

Manufacturer Part Number

330072-97

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

Fix Number

FIX10169973

Manufacturer Part Number

36480-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 10 Feet Long

Fix Number

FIX10173549

Manufacturer Part Number

448557-98

This replacement 10 foot power cord is specially produced for Black and Decker and Dewalt power tools. It is designed to connect to a standard US outlet supplying power to the tool. Please note one rubber insulated cord is included per order, the cord protector is not included it is sold separately. To complete this repair you will need a screwdriver.

Fix Number

FIX10166291

Manufacturer Part Number

148809-00

This is a genuine OEM sourced replacement part designed for use with a variety of power tools. Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. It is made out of rubber and it is sold individually.

Fix Number

FIX12523118

Manufacturer Part Number

N426848

This is an authentic Porter Cable replacement part manufactured for use with belt sanders. This is a three wire cord that is set in a sturdy jacket. The cordset is available as an individual replacement part, please see model diagram for additional parts.

Fix Number

FIX12488745

Manufacturer Part Number

N191071

This is an authentic part supplied directly from original manufacturer. It is commonly used with belt sanders. Its purpose is to deliver power to the tool. If the cord is damaged or torn it is important to replace it immediately. It is made from tough, thick outer rubber insulation for a long service life. Please note the cord protector/grommet is sold separately. Replacing this power cord should only require a screwdriver. • Remove housing screws • Separate housing • Disconnect wires • Remove old cord • Secure new cord in place • Reattach wires • Reassemble and test the unit