OEM DeWALT Planer Jointer Parts & Accessories

Sprocket

$9.02

Fix Number: FIX10168640
Manufacturer Part Number: 285928-00

This manufacturer-approved replacement sprocket is sold individually. Your planer feed rollers are driven by chains and sprockets. The outfeed roller has two sprockets on it, one connects it to the gearbox and the other connects to the infeed roller, the infeed roller also has a single sprocket, four in total on your planer. When the sprocket has worn down the chain will start to skip. If the planer is overloaded often, this might also cause the key on the sprocket to shear. This sprocket has eight teeth, a 5/8 bore with a 3/16 key inside the bore.

Carbide Tipped Blade

$15.02

Fix Number: FIX11925467
Manufacturer Part Number: 273794

This is a 3-1/4-inch reversible carbide tipped blade for a planer. It is an OEM authorized part and is sold individually. If the blade is chipped or is not performing as well as it once did, it should be replaced. The blade is what planes the workpiece and leaves a smooth finish. To remove the old blade, start by removing the drum cover. Unfasten the bolts that secure it in place. Use a screwdriver to slide the blade out of place and then pull it out to remove.

Adapter

$18.20

Fix Number: FIX10176243
Manufacturer Part Number: 5140011-48

Genuine Manufacturer Approved replacement part designed for certain DeWALT Planers. This part is made out of Plastic and it is Sold Individually. This Adapter allows you to connect Dust Chute to your unit.

Circuit Breaker

$19.30

★★★★★

1 Review

Fix Number: FIX10175758
Manufacturer Part Number: 5140000-19

This is a circuit breaker, which provides overload protection to your planer motor. It is OEM authorized and sold individually. If the planer is working with a very large piece of lumber and takes too large of a bite, this will put stress on the motor that it may not be able to handle. This is when the circuit breaker is designed to trip, which will turn the power off to the motor, protecting it from expensive damage. With time, the circuit breaker can fail, causing it to prematurely trip or not reset after being tripped. To access this part, start by removing the trim piece around the switch with a screwdriver. Next, remove the switch plate that secures the switch to the planer, and then use your pliers to remove the two wires attached to the old circuit breaker. Then use a wrench to unfasten the nut that secures the circuit breaker to the housing, which will allow you to then remove the circuit breaker.

Drive Chain

$12.79

Fix Number: FIX10168668
Manufacturer Part Number: 285960-00

This is a genuine drive chain for a planer. It is sold individually. Your planer feed rollers are driven by chains and sprockets. Over time, the chain can wear and stretch, causing it to skip on the sprockets. On rare occasions it can even break. Your planer has two of these chains and they are identical. For this repair you may need a screwdriver and snap-ring pliers.

Blade Clamp

$8.40

Fix Number: FIX10184095
Manufacturer Part Number: 663290-00

This is a genuine manufacturer-sourced replacement screw which is specially designed for use with DeWALT portable hand planers. It is an identical replacement for a missing or a faulty clamp that is utilized to secure the blade, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

Carbon Brush With Spring

$15.19

Fix Number: FIX10176277
Manufacturer Part Number: 5140011-85

This is a single carbon brush with a spring. Carbon brushes are what supply electricity to the armature. They are known to wear due to constant rubbing against the commutator, so it should not be a concern if they are in need of a replacement. They should be inspected regularly, especially if your power tool is not functioning properly. A worn brush can cause excessive sparks, however a damaged armature can also cause sparks, so you will need to inspect both parts. This is a simple repair that should only take a few minutes. You will need to remove the brush caps, and then align the new carbon brush in the holder with the tabs. You will need a screwdriver to secure the cap.

Bushing

$12.17

Fix Number: FIX10176062
Manufacturer Part Number: 5140006-82

This replacement bushing is an authentic high quality item that is sourced from original equipment manufacturer for use with Dewalt planers. Two of these bushings are used to secure the roller, please note this durable metal part is sold individually. Replacing this bushing will require a set of tools such as long nosed pliers, a screwdriver and a wrench set.

Bushing

$6.51

Fix Number: FIX10168655
Manufacturer Part Number: 285945-00

This is a single authentic bushing for a planer. It attaches on the end of the feed roller, and each unit will have four of these in total. Due to the rubbing of the metals, these bearings are known to deteriorate, and should be inspected regularly for damage and to check if they have become loose.

Sprocket

$9.68

★★★★★

1 Review

Fix Number: FIX10176181
Manufacturer Part Number: 5140010-81

This is a single OEM sprocket for a planer. The feed rollers on a planer are driven by chains and sprockets. The outfeed roller has two sprockets, and the infeed roller has one. When the sprocket wears this can cause the chain to skip. If the tool is consistently being overloaded, the key on the sprocket could also shear. As this part is sold individually, be sure to order the amount needed.

DeWALT Planer Jointer Parts

Popular DeWALT Planer Jointer Parts

DeWALT Planer Jointer Appliance Types

Related DeWALT Planer Jointer Parts

Popular DeWALT Planer Jointer Models

DeWALT Planer Jointer Parts

Start With Your Model Number

Popular DeWALT Planer Jointer Parts

DeWALT Planer Jointer Appliance Types

Related DeWALT Planer Jointer Parts

Popular DeWALT Planer Jointer Models