OEM DeWALT Jig Saw Parts & Accessories

Grease

$11.85

Fix Number: FIX10185142
Manufacturer Part Number: 870889-03

It is a genuine OEM sourced component which is specially produced for use with DeWALT and Black and Decker power tools. This petroleum based grease is used to lubricate the system allowing for easy low friction movement while protecting parts from the usual wear. Please note this high-quality item is sold individually.

Needle Bearing

$6.51

Fix Number: FIX10169646
Manufacturer Part Number: 330004-06

This needle bearing is an authentic OEM part. This piece is used in DeWALT and Black & Decker power tools including various saws and grinders. Bearings buffer and secure moving parts while reducing friction. Needle bearings have long rollers rather than balls. Bearings are highly worn parts and may need replacement often. This part is sold individually. Included in part number 398618-00 Gear Case Assembly

Plate, Sole

$6.51

Fix Number: FIX16687765
Manufacturer Part Number: N548480

Brush Spring

$6.51

★★★★★

1 Review

Fix Number: FIX10173420
Manufacturer Part Number: 445860-00

This is a brush spring and it is used in a variety of power tools. The spring applies force to the motor brush inside the motor. This will keep the brush tight along the armature. If the brush has worn down it will create heat, and the spring will lose tension. If this happens, both parts will have to be replaced.

Sole Plate

$9.06

Fix Number: FIX10180013
Manufacturer Part Number: 581268-00

This is a Genuine OEM Approved replacement part designed for use with Dewalt Jig Saws. This part is made out of Plastic and it is Sold Individually. This is the No-Mar Pad/Plate allowing for the tool to slide smoothly. To replace you do not need any tools. Simply place the front of the aluminum shoe into the front of the no-mar shoe cover and lower the jig saw. The no-mar shoe will click securely onto the rear of aluminum shoe

Plunger

$6.51

Fix Number: FIX10180253
Manufacturer Part Number: 584686-00

Shoe ( The Mounting Holes Are

$31.52

Fix Number: FIX10180010
Manufacturer Part Number: 581263-00

This is an authentic part from DeWALT for use in jig saws. The shoe attaches to the sole plate. When replacing this part a screwdriver might be required during the installation process. It will require replacing if it becomes broken. This is available as an individual replacement part.

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Watch the install video

Power Cord (10-foot)

$24.41

Fix Number: FIX10169874
Manufacturer Part Number: 330072-97

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

Watch the install video

Electric Drill Cord Protector

$9.74

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

DeWALT Jig Saw Parts

Popular DeWALT Jig Saw Parts

Installation Instructions

DeWALT Jig Saw Appliance Types

Related DeWALT Jig Saw Parts

Popular DeWALT Jig Saw Models

DeWALT Jig Saw Parts

Start With Your Model Number

Popular DeWALT Jig Saw Parts

Installation Instructions

DeWALT Jig Saw Appliance Types

Related DeWALT Jig Saw Parts

Popular DeWALT Jig Saw Models