Jig Saw Parts

Power Cord

$17.56

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Grinder Motor Brush

$7.87

Fix Number: FIX10106782
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Cord Set

$20.72

Fix Number: FIX17016229
Manufacturer Part Number: 344492750

This is an OEM 16-gauge cord for double insulated tools. It is sold individually, and measures 9 feet long. It is a two-wire cord with two prongs and does not require a ground wire. If the cord is cracked or damaged in any way, it should be replaced right away to avoid shock.

Brush

$7.87

Fix Number: FIX10215587
Manufacturer Part Number: 445861-25

Watch the install video

Carbon Brush Set CB-407

$10.85

Fix Number: FIX10156656
Manufacturer Part Number: CB407

This set comes with two carbon brushes with wire leads and brush strings attached. If your motor is not running efficiently or is operating intermittently, this is a common sign of worn brushes. Due to the friction they are constantly under, they will wear over time, and will start to appear cracked, pitted, or burnt if not replaced regularly. We recommend also taking a look at the armature to ensure it is not damaged. This brush set is compatible with multiple model types, so it is best to consult your user manual for repair instructions.

Watch the install video

Carbon Brush Set CB-75

$7.83

Fix Number: FIX10156669
Manufacturer Part Number: CB75

If your motor is running poorly, running intermittently, it is likely in need of new carbon brushes. This part includes a set of two carbon brushes with wire leads and brush springs attached. Changing the carbon brushes is part of your regular maintenance, so it is a good idea to have a few extra on hand. When replacing the carbon brushes, it is also advised to inspect the armature at the same time.

Carbon Brush/Lead (Sold Individually)

$5.89

Fix Number: FIX10122198
Manufacturer Part Number: 22-18-0710

This carbon brush lead or also known as a carbon motor brush fits the following tools: angle grinders, nibbler and shears, sander polishers, and jig saws. This includes the brush and a wire lead attached. This is one of the most commonly replaced power tool components because the carbon brushes easily wear off with friction and use. If your brush is worn out it can cause intermittent motor function, reduction in electric braking, and in motor power. If you notice burns and cracks on the wire lead, then it is best to replace this part. Tip: when replacing your carbon brush, make sure to inspect your armature for damage as well, in case there are larger motor problems.

Protector

$6.84

Fix Number: FIX10211611
Manufacturer Part Number: 330005-01

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Brush 120V (Sold Invididually)

$7.69

Fix Number: FIX10116514
Manufacturer Part Number: N031653

Carbon Brushes / Set

$15.47

Fix Number: FIX10416276
Manufacturer Part Number: 316034930

This is a carbon brush set for your power tools, most commonly your angle grinder. This purchase includes a set of 2 carbon brushes. It is known as a wear part because through friction and extended use, it will gradually wear out and require replacement. If you are experiencing reduced electric braking and delayed motor power, a worn brush is most likely the problem. When making this installation, inspect your armature for burns or cracks which could mean a larger motor issue.

Popular Jig Saw Parts

Installation Instructions

Installation Instructions

Brands

Related Pages

Popular Jig Saw Models

Jig Saw Parts

Start With Your Model Number

Popular Jig Saw Parts

Installation Instructions

Installation Instructions

Brands

Related Pages

Popular Jig Saw Models