OEM Porter Cable Jig Saw Parts & Accessories

BRUSH

$12.08

Fix Number: FIX18993191
Manufacturer Part Number: N031653

Genuine Porter Cable replacement part includes 1 Carbon Brush with wire lead and brush spring attached.rn • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

BRUSH

$13.35

Fix Number: FIX18985827
Manufacturer Part Number: 690741

Genuine Porter Cable replacement part rnIncludes 1 Carbon Brush with lead.rnrn n++ Worn brushes are often the cause of a poorly running motor n++ Replacing brushes can fix an intermittent motor n++ New brushes can restore a motorn++s electric braking Carbon motor brushes are one of the most commonly replaced power tool components.n++ Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement.n++ Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power.n++ A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned.n++ When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Watch the install video

Electric Drill Cord Protector

$10.75

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

LATCH CARRYING CASE

$6.51

Fix Number: FIX18987629
Manufacturer Part Number: 887712

This is a carrying case latch for your power tools, most commonly your nailer and drill. If your case is no longer staying closed, you can repair it by purchasing this replacement part. It is made of plastic, and is the latch only.

Blade Clamp

$8.31

★★★★★

1 Review

Fix Number: FIX10180085
Manufacturer Part Number: 582593-00

The job of the blade clamp is to secure the saw blade to the shaft of the jigsaw. The blade clamp is meant to make blade changes quick and easy with its quick-release design. Over the use of your tool, the clamp will begin to wear and this will result in its inability to hold the blade properly. This blade clamp is sold individually and sourced right from the original manufacturer.

Fixes these symptoms

Blade falls out
See more...

Installation Instructions

Glendale from LOS ANGELES, CA

Blade Clamp Replacement

1. Remove two (2) allen hex nut holding blade clamp to shaft.
2. Using a flathead screwdriver or plier, gently pry clamp downward away from shaft.
3. Installation is reverse. Slide new blade clamp to shaft, gently slide until hex nut holes align and insert nut and tighten down. Read more...

BEARING

$15.00

Fix Number: FIX12499559
Manufacturer Part Number: 859293

This is a needle bearing that is open on both sides. This genuine Porter Cable replacement part is sold individually. • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Watch the install video

Power Cord (10-foot)

$29.49

Fix Number: FIX10169874
Manufacturer Part Number: 330072-97

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

Grease

$13.08

Fix Number: FIX10185142
Manufacturer Part Number: 870889-03

It is a genuine OEM sourced component which is specially produced for use with DeWALT and Black and Decker power tools. This petroleum based grease is used to lubricate the system allowing for easy low friction movement while protecting parts from the usual wear. Please note this high-quality item is sold individually.

LOCKWASHER

$6.51

Fix Number: FIX18986735
Manufacturer Part Number: 802430

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Porter Cable equipment. It is a high-quality hardware which is generally utilized to provide a tight seal between connected parts, unfortunately, over time it may wear out or simply get lost eventually requiring a replacement. Keep in mind this high-quality item is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this lock washer.

Bearing, Ball

$6.51

Fix Number: FIX16680866
Manufacturer Part Number: 605040-06

This is replacement ball bearing is a commonly used item on a variety of power tools. Bearings are specially designed to allow connected parts to rotate smoothly. The way it is build it will minimize friction between the rotating parts. This is a sealed metal bearing generally used with an armature. Includes one (1) bearing per order. Steps to replace this bearing would be different from one model to another. However, general steps to complete this repair would be the same. You may need a screwdriver and pliers to finish this job. • Make sure the unit is unplugged • Remove the cover/housing • Disengage the brushes • Remove the armature • Remove the old bearing • Install the new bearing • Reassemble unit and test the equipment

Porter Cable Jig Saw Parts

Popular Porter Cable Jig Saw Parts

Installation Instructions

Porter Cable Jig Saw Appliance Types

Popular Porter Cable Jig Saw Models

Porter Cable Jig Saw Parts

Start With Your Model Number

Popular Porter Cable Jig Saw Parts

Installation Instructions

Porter Cable Jig Saw Appliance Types

Popular Porter Cable Jig Saw Models