Models
>
JV0600K
JV0600K Makita Jig Saw
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JV0600K
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
$32.12
This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing y...
In Stock
Order now and your part arrives by Aug 15
$12.74
If your motor is running poorly, running intermittently, it is likely in need of new carbon brushes. This part includes a set of two carbon brushes with wire leads and brush springs attached. Changing...
In Stock
Order now and your part arrives by Aug 15
$6.51
This is a self-tapping screw, and it is found on multiple power tools and lawn equipment. This screw is different because it can tap its own hole into tough materials, such as metals and hard plastics...
In Stock
Order now and your part arrives by Aug 15
$6.51
Genuine Makita replacement part, This item is sold individually. This screw is used mostly on the bases of the tool listed below. On the jig saws it is used to attach the Base Plate to the base. On t...
In Stock
Order now and your part arrives by Aug 15
$14.30
This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or r...
On Order
$6.51
This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it ha...
In Stock
Order now and your part arrives by Aug 15
$6.51
This 5 x 8 carbon brush holder is a genuine OEM replacement part used in various outdoor power equipment. It is a small plastic box with a cavity, and it is located near the engine assembly. The brush...
In Stock
Order now and your part arrives by Aug 15
$26.31
This authentic OEM part is compatible with various handheld power tools made by Makita including jig saws, routers, and sanders. A bearing\\\'s main purpose is to decrease friction between moving part...
In Stock
Order now and your part arrives by Aug 15
$6.51
It is a genuine item which is supplied directly from the original equipment manufacturer for use with Makita saws. The purpose of this flat washer is to provide a tight seal between connected parts, p...
On Order
$6.51
This is an authentic manufacturer-sourced part which is specially desgined for use with Makita power tools. The stop ring is commonly generally utilized to secure a component to a shaft or a spindle, ...
In Stock
Order now and your part arrives by Aug 15
$6.51
This is an authentic OEM sourced part which is specially made for use with Makita power tools. It is an identical replacement for a missing or a faulty steel ball that was installed on a new unit. Thi...
Special Order
$6.51
This is an authentic Makita replacement part manufactured for use with power tools. The pin is commonly used as a pivot point for a part assembly depending upon the model or type of tool. This pin is ...
In Stock
Order now and your part arrives by Aug 15
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from HILLSBORO, OR
- Parts Used:
- 664064-4
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Old power cord frayed at the grommet entering the drill casing
Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Was this instruction helpful to you?
Thank you for voting!