Ridgid Jig Saw Parts

Fix Number

FIX10098112

Manufacturer Part Number

516851001

This manufacturer sourced replacement part designed for use on Ridgid power tools. The purpose of the brush cap is to hold the brush in the tool. This cap has external threads that thread into the housing of the tool. Be careful when removing and replacing these, they have a tendency to break. This item is made out of plastic and it is sold individually. You would need a flathead screwdriver to install or remove this brush cap.

Fix Number

FIX10097940

Manufacturer Part Number

512777001

This is an authentic manufacturer-approved replacement part. It is specially designed for use with Ridgid equipment. It allows a user to secure the guide in the needed position once it is adjusted. This knob is consists of a durable metal threaded shaft with a plastic grip and is sold individually. Make sure to refer to the appropriate diagrams for your model for the exact location and the correct application. Replacing it does not require any special tools, remove the old knob and screw in the new one.

Fix Number

FIX18693929

Manufacturer Part Number

304034002

This genuine manufacturer-sourced component is specially designed for use with Ridgid compact jig saws. It is an identical replacement for a missing or a damaged assembly that was installed on a new unit. The part helps to guide the blade, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality assembly is made of durable metal and is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX18693570

Manufacturer Part Number

290848001

This is a genuine Ridgid replacement part. It is sold individually, 2 are needed to make a set. Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • Parts are sold individually • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10084424

Manufacturer Part Number

690258001

This is a genuine OEM sourced replacement part that is intended to be used with impact drivers and jig-saws from Ryobi and Ridgid. The metal retaining ring is used to secure the sleeve and spring to the bit holder assembly. This item may require small nose pliers to install and it is priced as a single item.

Fix Number

FIX10083851

Manufacturer Part Number

670914001

Fix Number

FIX12123518

Manufacturer Part Number

681761001

This genuine OEM sourced replacement ball bearing is a standard item which has multiple uses on a variety of power tools. Please check diagrams for proper application of this item. The bearing is specially designed to reduce friction between rotating parts. Over time it will wear out, at this point it should be replaced. This is a sealed metal bearing and it is sold individually.

Fix Number

FIX18695386

Manufacturer Part Number

516850001

It is an authentic manufacturer sourced replacement brush holder that is specially designed for Ridgid saws. The purpose of this part is to hold carbon brushes around the armature to provide stable and safe contact. This high quality brush holder is sold individually, please note carbon brushes are sold separately.

Fix Number

FIX10083885

Manufacturer Part Number

671319001

It is a genuine replacement part that is supplied by original equipment manufacturer for use with Ridgid and Ryobi jig saws and routers. This e-ring has a few different applications depending on the model of your tool, please make sure to check appropriate diagrams for correct location and use of this hardware. It is made of durable, high-quality metal and it is sold individually. When working with this component, it is best to use specially designed e-clip tool removal which is sold separately.

Fix Number

FIX10100714

Manufacturer Part Number

692670001