OEM Craftsman Jig Saw Parts & Accessories

Needle Bearing

$6.51

Fix Number: FIX10169646
Manufacturer Part Number: 330004-06

This needle bearing is an authentic OEM part. This piece is used in DeWALT and Black & Decker power tools including various saws and grinders. Bearings buffer and secure moving parts while reducing friction. Needle bearings have long rollers rather than balls. Bearings are highly worn parts and may need replacement often. This part is sold individually. Included in part number 398618-00 Gear Case Assembly

Brush Spring

$6.51

★★★★★

1 Review

Fix Number: FIX10173420
Manufacturer Part Number: 445860-00

This is a brush spring and it is used in a variety of power tools. The spring applies force to the motor brush inside the motor. This will keep the brush tight along the armature. If the brush has worn down it will create heat, and the spring will lose tension. If this happens, both parts will have to be replaced.

Watch the install video

Electric Drill Cord Protector

$9.74

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

COMPRESSION SPRING

$6.55

Fix Number: FIX19508952
Manufacturer Part Number: 2604610040

Cord/10ft./18-2

$25.71

Fix Number: FIX10173549
Manufacturer Part Number: 448557-98

This replacement 10 foot power cord is specially produced for Black and Decker and Dewalt power tools. It is designed to connect to a standard US outlet supplying power to the tool. Please note one rubber insulated cord is included per order, the cord protector is not included it is sold separately. To complete this repair you will need a screwdriver.

Shoe

$16.20

Fix Number: FIX10165784
Manufacturer Part Number: 133770-00

This jig saw shoe has been sourced from the original manufacturer to ensure a high level of quality. The metal shoe is intended to be used with jig saws from DeWalt and Black & Decker. This item attaches to the base of the motor housing and is used to provide a stable and level footing for the saw. This part is priced as a single item.

Blade Clamp

$7.67

★★★★★

1 Review

Fix Number: FIX10180085
Manufacturer Part Number: 582593-00

The job of the blade clamp is to secure the saw blade to the shaft of the jigsaw. The blade clamp is meant to make blade changes quick and easy with its quick-release design. Over the use of your tool, the clamp will begin to wear and this will result in its inability to hold the blade properly. This blade clamp is sold individually and sourced right from the original manufacturer.

Fixes these symptoms

Blade falls out
See more...

Installation Instructions

Glendale from LOS ANGELES, CA

Blade Clamp Replacement

1. Remove two (2) allen hex nut holding blade clamp to shaft.
2. Using a flathead screwdriver or plier, gently pry clamp downward away from shaft.
3. Installation is reverse. Slide new blade clamp to shaft, gently slide until hex nut holes align and insert nut and tighten down. Read more...

CARBON BRUSH SET

$17.01

Fix Number: FIX19508852
Manufacturer Part Number: 2604320910

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Brush Set

$6.51

Fix Number: FIX10184432
Manufacturer Part Number: 761819-00

This is an authentic replacement part manufactured for use with DeWalt, and Black and Decker power tools. Carbon brushes are considered a wear item because they are in constant contact with the spinning armature. Worn brushes can cause a lower level or performance, or cause the power tool to stop working altogether. Most power tools with a good amount of use will require the brushes to be replaced at some point. These brushes will come in a pair, and the pair is sold individually.

Craftsman Jig Saw Parts

Popular Craftsman Jig Saw Parts

Installation Instructions

Installation Instructions

Craftsman Jig Saw Appliance Types

Popular Craftsman Jig Saw Models

Craftsman Jig Saw Parts

Start With Your Model Number

Popular Craftsman Jig Saw Parts

Installation Instructions

Installation Instructions

Craftsman Jig Saw Appliance Types

Popular Craftsman Jig Saw Models