OEM DeWALT Circular Saw Parts & Accessories

Dust Bag Assembly

$11.00

Fix Number: FIX12522964
Manufacturer Part Number: N273733

This authentic OEM dust bag assembly is sourced from the original manufacturer for use in sanders. It consists of a fabric bag and plastic cap measuring approximately 5.5 inches in length and 2.5 inches in diameter. The bag assembly collects the dust and debris that is produced during sanding allowing you to maintain a clean and safe working environment. Over time the bag may tear or wear down, leading to large amounts of dust escaping into the air, health hazards from dust inhalation, reduction in visibility, and a messy work area. Replacing the dust bag assembly is a simple repair that does not require the use of specialized tools. Simply detach the bag from the sander, remove any dust and debris on the mounting surface, and attach the new bag.

Blade Bolt

$6.51

Fix Number: FIX10183641
Manufacturer Part Number: 648697-00

This circular saw blade bolt is sold individually and genuinely sourced. This bolt fastens the blade to the spindle/shaft. If this part is damaged or missing the blade may become wobbly and unsafe to use. For this simple repair, you will need a hex key/Allen wrench to tighten and loosen this bolt.

Carbon Brush With Spring

$10.77

Fix Number: FIX10173724
Manufacturer Part Number: 450374-12

This is a brush and spring for your power tools. This brush is sold individually, and two are needed for most power tools. We recommend replacing both brushes together for an even wear. When your brush wears down it will greatly affect your motor function by reducing the power and electric braking. When making this repair we recommend inspecting the armature for cracks or visible damage that would mean other motor problems. Carbon brushes are the most commonly replaced power tool part. This part is meant to wear out over time through the constant contact.

Bolt

$6.51

Fix Number: FIX10166064
Manufacturer Part Number: 145344-00

This is an OEM part sourced directly from the manufacturer. The screw is found in Craftsman circular saws. This is a metal part, used to hold other components to the spindle assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

Outer Clamp Washer

$6.51

Fix Number: FIX16688623
Manufacturer Part Number: N621119

This outer clamp washer is specially designed for use with Dewalt circular saws. It is an authentic item supplied directly from original equipment manufacturer. This washer helps to secure saw blades to the spindle-shaft. Includes one (1) metal outer clamp washer per order. Please note, the inner clamp and the blade bolt are both sold separately. You will need a wrench to remove and install the blade bolt when replacing this clamp washer.

Brush and Spring

$12.60

★★★★★

1 Review

Fix Number: FIX10166057
Manufacturer Part Number: 145323-06

This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.

Fixes these symptoms

Won't turn on
See more...

Watch the install video

Ball Bearing

$17.55

★★★★★

1 Review

Fix Number: FIX10169632
Manufacturer Part Number: 330003-64

This is a ball bearing for your power tools. It is used in a variety of machines for rotary motion. The bearings support your tools by lowering the friction, which allows easy rotation of moving parts. Depending on how often you use your tool the bearings are a commonly replaced part. This is because they will experience most of the pressure, heat, and vibrations.

Installation Instructions

Michael from NEW BERLIN, WI

Bad bearing on brush end of Bucksaw motor

remove the brush cover on the end oppisite blade, unplug brush and remove bronze brusholder, if not replacing brushes , mark them for left and right. In my case the bearing had seized to the armature shaft much tighter than its normal shrink fit, so a bearing puller was needed, once the bearing is off, clean up shaft , heat bearing to about 200 deg F and blast end of shaft with cyrofreeze -60 F quickly drop bearing onto shaft and with very little effort it should slide on and bottom out on shaft. work quickly the shrink fit only lasts a few seconds. the trick is to heat bearing but not get it too warm and distort the plastic bearing cover. reinstall brush cap and old or new brushes. these old bucksaws are great for siding jobs , problem is only thing still available is the bearings and brushes. I think this saw is 35-40 years old , maybe I can get another 10 years out of it and by then I will be too old to lift it. Read more...

Watch the install video

Brush

$18.58

Fix Number: FIX10170261
Manufacturer Part Number: 381028-08

This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.

Watch the install video

Ball Bearing

$7.62

Fix Number: FIX10180911
Manufacturer Part Number: 605040-27

This part includes one OEM ball bearing. This ball bearing is sealed on both sides. They are designed to minimize friction between moving parts and evenly distribute weight. Bearings are a general wear part that require regular maintenance to keep your equipment running smoothly and efficiently.

Cord Protector

$7.89

★★★★★

3 Reviews

Fix Number: FIX10173396
Manufacturer Part Number: 445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

DeWALT Circular Saw Parts

Popular DeWALT Circular Saw Parts

Installation Instructions

DeWALT Circular Saw Appliance Types

Related DeWALT Circular Saw Parts

Popular DeWALT Circular Saw Models

DeWALT Circular Saw Parts

Start With Your Model Number

Popular DeWALT Circular Saw Parts

Installation Instructions

DeWALT Circular Saw Appliance Types

Related DeWALT Circular Saw Parts

Popular DeWALT Circular Saw Models