Circular Saw Parts

Popular Circular Saw Parts

Fix Number
FIX10170261
Manufacturer Part Number
381028-08
This carbon brush fits a variety of gardening and lawn tools. The brush is a common replacement part and can easily fix most motor malfunctions. This brush comes with a wire lead and a connection terminal. Inspect the wire lead for any damage and replace immediately if burns or cracks are noticed. Refer to the diagram provided by the manufacturer for installation instructions.
Brush Assembly
$5.95
In Stock
Fix Number
FIX10122139
Manufacturer Part Number
22-18-0075
This authentically sourced replacement carbon brush has a wire lead, brush spring, and bracket attached. This brush is sold individually, however, your tool requires two brushes to operate. If your motor is running poorly, worn brushes are the most common reason. A worn brush usually shows wear near the wire lead and sometimes has cracks or burns. We highly suggest checking the armature for burns at the same time, as this might indicate a more serious issue with your motor.
Carbon Brush Set
$10.85
In Stock
Fix Number
FIX10156649
Manufacturer Part Number
CB303
The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.
Table Saw Saw Carbon Brush
$11.54
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10166057
Manufacturer Part Number
145323-06
This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.
Carbon Brush Set
$10.85
In Stock
Fix Number
FIX10156641
Manufacturer Part Number
CB154
This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric braking power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.
Reciprocating Saw Shoe Assembly
$15.49
In Stock
Fix Number
FIX10132586
Manufacturer Part Number
45-16-0645
The shoe assembly is located at the front of the reciprocating saw and helps to direct the blade while you cut. The most common reason this part is replaced is just from simply misplacing it. If the saw is used roughly, the pivot hinge between the mounting bar and the shoe can damage, which can cause the shoe to fall off. Never use your saw without this part intact as it could cause damage to your equipment. For this easy repair, use your Allen wrench to remove the screws and this will allow you to remove the shoe. To install the new shoe assembly, line up the forks with the housing and slide it into position. To finish, tighten the screws back up and it is ready to go.
Power Cord
$36.89
In Stock
Fix Number
FIX10169913
Manufacturer Part Number
330079-98
It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long
Switch
$26.42
In Stock
Fix Number
FIX10123797
Manufacturer Part Number
23-66-2635
10-24 X 1/2" Pan HD. Sit. Tapt. T-25
$4.99
In Stock
Fix Number
FIX10118952
Manufacturer Part Number
06-82-5314
This part includes one pan head torx screw. It is sourced directly from the original manufacturer, ensuring a premium high-quality screw. It is compatible with a variety of equipment, so will serve various applications. It measures 10-24 by 1/2. Be sure to use the appropriate size tool to loosen and tighten it so it does not get damaged.
Circular Saw Strain Reliever
$10.00
Special Order
Fix Number
FIX10113583
Manufacturer Part Number
901266
This is a strain reliever for your power tools. It found at the meeting place between your cord, and the outer tool housing. The relief is an important part for your power tool because it protects your cord from tearing and breaking due to constant pressure. Keep your relief in good condition because it will extend the life of the cord, and the machine overall.

Installation Instructions

Jeff from WISC RAPIDS, WI
Strain reliever broken at base of saw. Core frayed.
1. Unplug saw. 2.Examine and determine which parts need to be removed to gain access to switch. 3.Remove screws one at a time and placed in dish keeping track of size and length of where removed from handle. 4. Slowly pull handle apart exposing switch and wires. 5. Remove screws holding black and white wires keeping track of which wire goes where. 6. Thread new power cord the same way the old one was positioned though the handle and reassemble. Read more...

Circular Saw Brands

Related Circular Saw Parts

Popular Circular Saw Models