OEM Milwaukee Circular Saw Parts & Accessories

Transparent Window

$6.51

Fix Number: FIX17081893
Manufacturer Part Number: 44-06-0201

Bevel Adjustment Knob

$6.51

Fix Number: FIX10130819
Manufacturer Part Number: 43-98-0705

This is an authentic OEM part. The Milwaukee bevel adjustment knob is compatible with Cordless M18 Fuel Circular Saws. This plastic and metal item is fitted onto the rip fence spring, allowing the operator to secure the preferred shoe angle. The bevel adjustment knob is sold individually. An adjustable wrench may be needed for the repair. Please refer to the specific manual for additional instructions.

Brush Assembly

$6.51

Fix Number: FIX10122139
Manufacturer Part Number: 22-18-0075

This authentically sourced replacement carbon brush has a wire lead, brush spring, and bracket attached. This brush is sold individually, however, your tool requires two brushes to operate. If your motor is running poorly, worn brushes are the most common reason. A worn brush usually shows wear near the wire lead and sometimes has cracks or burns. We highly suggest checking the armature for burns at the same time, as this might indicate a more serious issue with your motor.

Brush Assembly

$6.62

Fix Number: FIX10122134
Manufacturer Part Number: 22-18-0035

This is genuine replacement carbon brush sourced from original manufacturer. It is designed for use with Milwaukee circular saw. This assembly includes one (1) carbon brush with a lead wire and a spring attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • Remove screws from the motor housing • Take off motor cover to gain access to the brushes • Take out old brushes and replace them with the new ones • Re-assemble and test the tool

Switch

$32.95

Fix Number: FIX10123797
Manufacturer Part Number: 23-66-2635

Intermittent motor operation, a sticking trigger, or failure to start can point to a damaged saw switch, but several nearby components can cause the same symptoms. Check the battery charge, terminals, lockout button, loose wires, and control electronics before ordering a replacement. The switch mounts inside the handle and responds when the operator presses the trigger after releasing the safety lock. Match it to the exact tool model and serial prefix. Remove the battery and cutting blade before service, then note the position of each wire and terminal. Avoid pinched wires during reassembly. Test that the lockout blocks accidental starting and that the motor stops when the trigger is released.

Brush Tube Assembly

$6.51

Fix Number: FIX10122384
Manufacturer Part Number: 22-22-1030

This is a manufacturer sourced replacement part used on a Milwaukee power tools. This part holds carbon brushes around the armature to provide stable and safe contact. Please note brushes are sold separately. This part is made out of plastic and metal. It is sold individually. To replace this assembly you would need a screwdriver and pliers. • First remove screws holding the cover together • Separate two (2) halves of the housing to gain access to armature and brush holder • Remove the old brush holder • Install the new brush holder, brushes and the armature • Reassemble and test your tool

Carbon Brush

$22.41

Fix Number: FIX10122203
Manufacturer Part Number: 22-18-0730

This is a carbon brush, used in a multiple different power tools. It is recommended to replace both carbon brushes at the same time even if only one appears worn. This part includes one manufacturer-approved carbon brush, so you may wish to order two. Carbon brushes are a very common replacement part and should be checked and replaced as part of your power tools regular maintenance. When inspecting the carbon brushes, it is also advisable to check the condition of the armature, especially if sparks were present.

Inner Blade Flange

$6.55

★★★★★

1 Review

Fix Number: FIX10129996
Manufacturer Part Number: 43-34-0790

This is an original manufacturer approved replacement part specially designed for use with Milwaukee circular saws. The purpose of this flange is to helps securing the grinding wheel to the spindle/shaft. It is a metal part and it is sold individually. You would need a wrench to remove blade bolt when replacing this flange.

Washer

$6.51

Fix Number: FIX10133420
Manufacturer Part Number: 45-88-1560

This is a washer designed for use within various models of circular saws. This is a flat washer that is used within the gear case assembly to secure the shoe assembly, the part that guides the saw and prevents digging, to the saw. This washer serves multiple different purposes on the saw, so it can be used in a variety of different applications.

Outer Flange Blade

$7.65

Fix Number: FIX10129997
Manufacturer Part Number: 43-34-0795

This is an original Milwaukee replacement item designed for use with circular saws. It is supplied by original equipment manufacturer. This item helps to secure saw blade to the spindle/shaft. This is a metal outer flange and it is sold individually. Please note you would need a wrench to remove the blade bolt when replacing a flange.

Milwaukee Circular Saw Parts

Popular Milwaukee Circular Saw Parts

Milwaukee Circular Saw Appliance Types

Related Milwaukee Circular Saw Parts

Popular Milwaukee Circular Saw Models

Milwaukee Circular Saw Parts

Start With Your Model Number

Popular Milwaukee Circular Saw Parts

Milwaukee Circular Saw Appliance Types

Related Milwaukee Circular Saw Parts

Popular Milwaukee Circular Saw Models