OEM Ridgid Circular Saw Parts & Accessories

Spring Washer

$6.51

Fix Number: FIX10084051
Manufacturer Part Number: 680776001

This is an authentic manufacturer-sourced part. It is specially designed for Ridgid and Ryobi circular saws. It helps to distribute the pressure evenly and provide a tight fit for the blade. If a spring washer on your equipment is damaged or is missing it will provide an identical replacement for the component that was included with a new unit. Keep in mind this high-quality hardware is made of durable metal and is sold individually. You will need a wrench to remove and resecure the blade bolt to replace this spring washer.

Collet 1/4 Inch

$6.51

Fix Number: FIX16755887
Manufacturer Part Number: 690045003

This genuine component is supplied directly from the original equipment manufacturer for use with Ryobi power tools. The collet allows a user to secure a bit. Note, it is for using bits with 1/4

LEVER

$6.51

Fix Number: FIX18695507
Manufacturer Part Number: 522691002

This is an authentic Ridgid replacement part that has been sourced from the original manufacturer to be used with circular saws. The durable plastic lever is used to turn the hex nut that secures the bevel or depth bolts. This item is used when adjusting the position of the blade depth or angle. This item is sold as an individual part.

Brush Holder

$6.51

Fix Number: FIX16236279
Manufacturer Part Number: 089037012106

This part is an OEM from Ridgid for use in table saws. The brush holder goes between the brush and the motor housing. A screwdriver may be required to replace this item if it becomes broken. This part is made out of plastic and metal and is available individually.

Bearing Ball 608zz

$6.40

Fix Number: FIX11858686
Manufacturer Part Number: 680141022

Genuine Manufacturer Approved replacement part used on a variety of Power Tools. This Ball Bearing has multiple applications depending on your tool. This part is made out of Metal and it is Sold Individually. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. To replace this Bearing you would need a Screwdriver and a Set of Wrenches.

SWITCH

$12.91

Fix Number: FIX18699825
Manufacturer Part Number: 760677015

This is a genuine Ridgid part that is sourced from the original manufacturer to be used with circular saws. The special switch allows a user to turn the tool on and off. It is an identical replacement for a missing or a faulty part that is installed on a new tool. When performing this repair, make sure to refer to the owner's manual and the parts diagrams for your model. Note, the switch is made of durable materials and is sold as an individual item.

ASSEMBLY BRUSH

$6.51

★★★★★

1 Review

Fix Number: FIX18693523
Manufacturer Part Number: 290069406

Genuine Ridgid replacement part, this item is sold individually. 2 of these Brushes are needed for a set. This Brush includes the Brush, Brush Holder, Brush Spring and plug in terminal. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Tile Saw Ball Bearing

$6.51

Fix Number: FIX9995584
Manufacturer Part Number: 671498001

BRUSH HOLDER CAP

$6.51

Fix Number: FIX18687790
Manufacturer Part Number: 089041033191

It is an authentic OEM sourced replacement part which is specially produced for use with Ridgid power tools. This part is generally utilized to secure the carbon brush in the brush holder, keep in mind his cap has external threads that thread into the housing of the tool. Please note this durable cap is made of high-quality plastic and is sold individually. You will need a flat-head screwdriver to install or remove this brush holder cap.

OUTER BLADE WASHER

$6.51

Fix Number: FIX18698883
Manufacturer Part Number: 680775003

This replacement outer blade washer is an authentic OEM sourced item that is specially designed for use with Ridgid circular saws. This part helps to secure the saw blade to the spindle. This durable metal item is sold individually, please note the inner washer and the blade bolt are both sold separately.

Ridgid Circular Saw Parts

Popular Ridgid Circular Saw Parts

Ridgid Circular Saw Appliance Types

Related Ridgid Circular Saw Parts

Popular Ridgid Circular Saw Models

Ridgid Circular Saw Parts

Start With Your Model Number

Popular Ridgid Circular Saw Parts

Ridgid Circular Saw Appliance Types

Related Ridgid Circular Saw Parts

Popular Ridgid Circular Saw Models