OEM Black and Decker Circular Saw Parts & Accessories

Power Cord

$40.44

Fix Number: FIX10169913
Manufacturer Part Number: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Bolt

$6.51

Fix Number: FIX10166064
Manufacturer Part Number: 145344-00

This is an OEM part sourced directly from the manufacturer. The screw is found in Craftsman circular saws. This is a metal part, used to hold other components to the spindle assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

Ball Bearing

$23.53

Fix Number: FIX16680871
Manufacturer Part Number: 605040-20

This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Carbon Brush With Holder

$12.68

★★★★★

2 Reviews

Fix Number: FIX10165739
Manufacturer Part Number: 132254-07

This is a genuine carbon brush with the holder, sold as one part. If your equipment requires two carbon brushes and holders, you will need to add two to cart. The carbon brush and holder are responsible for transferring electric current to the spinning armature in the motor. If your equipment will not start, the most common reason for this is due to a worn brush. This repair has taken most of our customers less than fifteen minutes to complete and is considered easy to medium difficulty. For this repair you will need screwdriver.

Carbon Brush With Wire Lead An

$6.51

Fix Number: FIX10170841
Manufacturer Part Number: 387558-01

Genuine DeWalt replacement part. rnIncludes 1 Carbon Brush with wire lead and terminal in rubber sheath attached.rnrn • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

Cord Protector

$8.70

★★★★★

3 Reviews

Fix Number: FIX10173396
Manufacturer Part Number: 445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

Outer Blade Clamp

$8.77

★★★★★

1 Review

Fix Number: FIX10166063
Manufacturer Part Number: 145343-01

This is a genuine replacement outer blade clamp specially made for circular saws. This part helps to secure the blade to the unit. A wrench would be needed to remove the blade bolt when replacing this clamp. It is made out of metal and it is sold individually.

Watch the install video

Power Cord

$49.20

Fix Number: FIX10169908
Manufacturer Part Number: 330078-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 16 Gauge • 10 Feet Long

Watch the install video

Holder

$33.41

Fix Number: FIX10166161
Manufacturer Part Number: 147097-09

This is a genuinely sourced carbon brush and holder. This carbon brush includes the holder, terminals, and spring, making it ready for installation. Consider replacing both brushes at the same to ensure even wear and peak motor performance. Be sure to inspect the carbon brushes frequently to keep your equipment running smoothly for years to come.

Brush and Spring

$13.91

★★★★★

1 Review

Fix Number: FIX10166057
Manufacturer Part Number: 145323-06

This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.

Fixes these symptoms

Won't turn on
See more...

Black and Decker Circular Saw Parts

Popular Black and Decker Circular Saw Parts

Black and Decker Circular Saw Appliance Types

Related Black and Decker Circular Saw Parts

Popular Black and Decker Circular Saw Models

Black and Decker Circular Saw Parts

Start With Your Model Number

Popular Black and Decker Circular Saw Parts

Black and Decker Circular Saw Appliance Types

Related Black and Decker Circular Saw Parts

Popular Black and Decker Circular Saw Models