OEM Makita Circular Saw Parts & Accessories

Circular Saw Trigger Switch

$30.16

Fix Number: FIX10153579
Manufacturer Part Number: 651172-0

This trigger switch is for circular saws. Trigger switch starts and stops the circular saw. Unplug the circular saw before installing this part. Wear work gloves to protect your hands.

Power Cord

$39.60

Fix Number: FIX10153852
Manufacturer Part Number: 664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

Carbon Brush Set Cb-203

$21.19

Fix Number: FIX10156645
Manufacturer Part Number: CB203

This part includes two carbon brushes with the wire leads and brush springs attached. In order for your motor to run at peak performance, it is imperative that the carbon brushes are well-maintained. The carbon brushes are needed to conduct electricity to the armature through the commutator. Over time these brushes wear down due to the constant rubbing. They should be regularly inspected to ensure your equipment continues to run smoothly. This repair should only take a few minutes.

Watch the install video

Shoe Base

$34.05

Fix Number: FIX10140499
Manufacturer Part Number: 163378-3

This shoe base is supplied directly from the original equipment manufacturer. Compatible with many circular saws, this metal component is sold individually. For making the replacement, you will need a screwdriver and pliers. It is also recommended to refer to the manual for further repair instructions.

Carbon Brush Set

$16.59

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric braking power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Carbon Brush CB-124 (Set of 2)

$12.74

★★★★★

1 Review

Fix Number: FIX10156640
Manufacturer Part Number: CB124

Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.

Carbon Brush Set

$10.36

Fix Number: FIX10156663
Manufacturer Part Number: CB441

This is a set of two carbon brushes. The carbon brushes should be checked on a regular basis. If they have worn down to the limit mark, it is time for a replacement. Both carbon brushes need to be replaced at the same time. For this repair use your screwdriver to detach the brush holder caps, remove the old carbon brushes, and insert the new ones. Fasten the new carbon brushes to the holder caps. To break in the new carbon brushes, run the tool with no load for about one minute.

Watch the install video

Compression Spring

$6.51

Fix Number: FIX10143551
Manufacturer Part Number: 233376-2

This is a genuine Makita replacement part, it is sold individually. The 233376-2 Spring is part of the spindle lock system on the Grinders shown below. The reason for locking the spindle is so that you can remove and replace grinding wheels. The other parts need for the spindle lock system are part numbers. • 417771-6 Pin cap • 256486-8 Shoulder Pin • And 256486-8 O Ring.

Carbon Brush Set

$16.59

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Ball Bearing 6000ddw

$14.30

Fix Number: FIX10141492
Manufacturer Part Number: 210059-1

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

Makita Circular Saw Parts

Popular Makita Circular Saw Parts

Makita Circular Saw Appliance Types

Related Makita Circular Saw Parts

Popular Makita Circular Saw Models

Makita Circular Saw Parts

Start With Your Model Number

Popular Makita Circular Saw Parts

Makita Circular Saw Appliance Types

Related Makita Circular Saw Parts

Popular Makita Circular Saw Models