OEM Makita Angle Grinder Parts & Accessories

Carbon Brush Set

$35.36

Fix Number: FIX10156646
Manufacturer Part Number: CB204

This is a set of two OEM carbon brushes with wire leads and brush springs. To ensure your motor is running efficiently, it is important to continually inspect the carbon brushes, as they are a common wear part. If they are damaged this will greatly affect the performance of the motor. If burns or cracks are present, it is advised to inspect the armature as well.

Carbon Brush Set

$16.59

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Cord Guard

$6.51

★★★★★

1 Review

Fix Number: FIX10153921
Manufacturer Part Number: 682505-8

This cord guard or strain reliever prevents cord damage by covering the last portion of a cord before entering a tool. This provides extra support and rigidness. The cord fits garden and lawn equipment. With use, the cord guard can break down and your cord is left unprotected, in this case it is best to replace the guard. Refer to the diagram provided by the manufacturer for installation instructions.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Carbon Brush Set

$16.59

Fix Number: FIX10156651
Manufacturer Part Number: CB311

Genuine Makita replacement part Set of 2 Carbon Brushes with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Watch the install video

Carbon Brush Set

$16.59

Fix Number: FIX10156657
Manufacturer Part Number: CB408

This part includes two carbon brushes with wire leads and brush springs. Worn brushes are typically presented as a failed or underperforming motor. Carbon brushes are a part that commonly wears, so it is a good idea to have these on hand. They are essential for a properly running motor because they conduct electricity to the armature. For this repair, you will start by removing the first brush from the motor, using a screwdriver to remove the brush cap. Once the cap is removed, the brush can be removed. Align the new brush with the holder and then reinstall the cap. Repeat these same steps for the other brush.

Power Cord

$39.60

Fix Number: FIX10153852
Manufacturer Part Number: 664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

Watch the install video

Pin Cap

$6.51

Fix Number: FIX10150565
Manufacturer Part Number: 417771-6

Genuine Makita replacement part, this item is sold individually. The Pin Cap is part of the spindle lock assembly for the Makita Tool model numbers shown below. When it is pressed it will stop the spindle from rotating, so that a grinding wheel or blade can be removed or installed.

Watch the install video

Carbon Brush Set

$10.28

Fix Number: FIX10156652
Manufacturer Part Number: CB325

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Watch the install video

Power Cord

$32.12

Fix Number: FIX10153834
Manufacturer Part Number: 664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Power Tool Power Cord

$33.76

★★★★★

1 Review

Fix Number: FIX10153842
Manufacturer Part Number: 664265-4

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Makita Angle Grinder Parts

Popular Makita Angle Grinder Parts

Installation Instructions

Installation Instructions

Makita Angle Grinder Appliance Types

Related Makita Angle Grinder Parts

Popular Makita Angle Grinder Models

Makita Angle Grinder Parts

Start With Your Model Number

Popular Makita Angle Grinder Parts

Installation Instructions

Installation Instructions

Makita Angle Grinder Appliance Types

Related Makita Angle Grinder Parts

Popular Makita Angle Grinder Models