Ridgid Angle Grinder Parts

Fix Number

FIX18696429

Manufacturer Part Number

591275001

Fix Number

FIX18693654

Manufacturer Part Number

300160017

This is a genuine manufacturer-approved replacement component which is specially designed for use with Ridgid angle grinders. It is the side handle that provides a user with a comfortable and safe grip for operating the unit. It is made of high-quality plastic with metal and is sold individually, no tools needed to replace this part.

Fix Number

FIX18695362

Manufacturer Part Number

515885001

It is an authentic OEM part which is made for Ridgid angle grinders. This is the special spacer which is secured between the guard and the output shaft assembly. If the hardware is missing or is damaged, this will provide an identical replacement for the original component that was installed on a new unit. This high-quality spacer is made of durable material and is sold as an individual item. Refer to the owner's manual and the appropriate diagram for your model to ensure the proper replacement procedure. A screwdriver will be needed to remove and reattach the guard when performing this repair.

★★★★★

★★★★★

1 Review

Fix Number

FIX18693523

Manufacturer Part Number

290069406

Genuine Ridgid replacement part, this item is sold individually. 2 of these Brushes are needed for a set. This Brush includes the Brush, Brush Holder, Brush Spring and plug in terminal. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10097976

Manufacturer Part Number

513101001

This is an authentic replacement part manufactured for use with Ridgid belt sanders, and angle grinders. The brush holder is used to support the brush within the tool's housing. This brush holder is sold as an individual replacement part, please note the brushes are available separately.

Fix Number

FIX18699817

Manufacturer Part Number

760518002

This is a genuine manufacturer-approved replacement switch that is specially designed for Ridgid angle grinders. It is the part of the tool handling on/off and variable speed operations. Over time due to mechanical or electrical problems components may begin to fail and eventually need a replacement. The switch has a durable plastic body and it is sold individually.

Fix Number

FIX18697348

Manufacturer Part Number

634192002

It is an authentic OEM sourced item which is specially produced for use with grinders made by Ridgid. The wrench is a special tool that is used to replace the flange. This tool may become broken and will need to be replaced. It is made of metal and is available as an individual replacement.

Fix Number

FIX18697286

Manufacturer Part Number

632223001

An authentic Ridgid replacement spanner wrench that is supplied by original equipment manufacturer for use with angle grinders. This wrench allows user to secure or remove the clamp nut that holds the grinding disk. This wrench is made from strong durable metal and it is sold individually.

Fix Number

FIX18698648

Manufacturer Part Number

672503001

This backing flange is a high quality replacement part that helps to secure the grinding disk. It is a genuine OEM supplied item that is specially designed for use with Ridgid grinders. Please note this durable metal item is sold individually.

Fix Number

FIX18698653

Manufacturer Part Number

672592001

This item is a genuine Ridgid replacement part that is intended to be used with angle grinders. The metal spring is a direct replacement of the original spring that was installed onto the grinder when new. This part is used to keep the handle lock button upright in the lock position and to allow the button to be compressed when rotating the handle to a different position. The spring is priced as a single item.