Angle Grinder Brackets and Flanges

Fix Number

FIX10188627

Manufacturer Part Number

N134467

This is an Original Manufacturer Sourced replacement part used on Dewalt Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Hex Hole Flange Nut is to hold the Grinding Wheel to the Spindle Shaft. You would need Hex Wrench to secure this part.

Fix Number

FIX10130006

Manufacturer Part Number

43-34-0935

This is an OEM inner disc flange, which is found on the spindle of a handheld grinder. Its function is to secure the grinding wheel to the spindle and providing support to the wheel, along with the flange nut (sold separately). It has a 5/8-inch non-threaded hole and a recess in it that engages with the spindle, and a 7/8-inch hub to accept a standard grinding wheel. This part is prone to wear and tear, which can lead to an unbalanced wheel. This is a simple repair that should only take a few minutes and should only require a wrench.

Fix Number

FIX10182961

Manufacturer Part Number

633257-00SV

This is an authentic OEM flange for angle grinders. It works with the nut (sold separately) to secure the grinding wheel to the gear case. It is imperative that they are maintained and inspected regularly to ensure they are still in good working condition to ensure no additional stress is put on the wheel. When making this repair, do not over-tighten the flange, as this could cause it to warp. This flange has 5/8-inch bore and is sold as an individual part.

Fix Number

FIX10171979

Manufacturer Part Number

397616-00

This is a Genuine replacement part used on some Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Inner Flange is to hold the Grinding Wheel to the Spindle Shaft.

Fix Number

FIX17081388

Manufacturer Part Number

43-34-0937

Fix Number

FIX10142400

Manufacturer Part Number

224399-1

This is an Original replacement part used on certain Makita Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Flange is to hold the Grinding Wheel to the Spindle Shaft.

Fix Number

FIX10184418

Manufacturer Part Number

761368-00

This is a genuine replacement bracket assembly. It is supplied directly from original equipment manufacturer for use with bench grinders. This bracket helps to secure the eyeshield to the main unit. It is made out of metal and it is sold individually. Please note the hardware and the eyeshield are both sold separately. To complete this repair you would need a screwdriver and a wrench. • Make sure the unit is unplugged • Remove the screws that secure the eyeshild • Remove the nut and the carriage bolt • Replace old bracket with a new one • Reassemble in reverse order

Fix Number

FIX10184420

Manufacturer Part Number

761370-00

This item has been sourced from the original manufacturer and is intended to be used with bench top grinders from Black & Decker and DeWalt. The metal bracket attaches to the top of the left wheel guard and is used to mount the left side eye shield. The bracket can be purchased as a single item, please note the hardware and eye shield are separate items.

Fix Number

FIX10165237

Manufacturer Part Number

054339-00

The flange fits between the clamp nut and the guard assembly. This part is an OEM from DeWALT and Black & Decker for use in angle grinders. This high-quality item is made of metal and is sold individually. It might become broken and will need to be replaced and a screwdriver may be needed during the replacement of this part.

Fix Number

FIX10134064

Manufacturer Part Number

49-05-0041

This is an Original replacement part used on certain Milwaukee Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Flange is to hold the Grinding Wheel to the Spindle Shaft. Flange designed to accommodate 7/8 In. hub depressed center wheel.