Angle Grinder Brushes

Fix Number

FIX17062120

Manufacturer Part Number

NA121629

Genuine Dewalt replacement part used on Small Angle Grinder. This brush has a lead wire attached and it is Sold Individually. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10122192

Manufacturer Part Number

22-18-0680

This carbon brush is used on a variety of cordless tools and tools. *Please note: This part is sold individually. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it can cause disruption in the functioning of the motor and reduce electric braking. If you notice cracks, burns and other damage on wire lead, then it is best to replace it to restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

★★★★★

★★★★★

1 Review

Fix Number

FIX10188358

Manufacturer Part Number

N097696

Genuine Dewalt replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10156649

Manufacturer Part Number

CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Fix Number

FIX10156653

Manufacturer Part Number

CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX19500958

Manufacturer Part Number

1607000V61

This carbon brush set replaces worn brushes in select power grinders to restore steady motor performance and prevent issues like power loss, excess sparking, or intermittent operation. The set includes the brushes, springs, and holders needed for a proper fit, helping the tool run smoothly and reliably again. Designed for specific grinder models, it offers a straightforward repair solution when the motor begins to hesitate or fail to start. Checking your tool’s model number is recommended to ensure the correct match.

Fix Number

FIX10156641

Manufacturer Part Number

CB154

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric braking power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX10183735

Manufacturer Part Number

650916-01

Sold Individually This motor brush is for angle grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the angle grinder before installing this part. Wear work gloves to protect your hands.

Fix Number

FIX10122265

Manufacturer Part Number

22-18-2240

This is an authentic set of two carbon brushes, including the brush, holder, and spring. This is one of the most regularly replaced parts in a power tool due to the constant friction created and leading to wear. If the motor is not functioning properly, a worn brush is usually the cause. We suggest also checking the armature for damage at the same time as this may suggest a more serious problem with the motor.

Fix Number

FIX10156652

Manufacturer Part Number

CB325

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.