Angle Grinder Power Cords

Fix Number

FIX19516305

Manufacturer Part Number

3604460555

This cord is a genuine OEM replacement part and is sold individually. Power Cord Specifications: 2 Wires. 18 Gauge. 2 Prongs. 6-1/2 Feet Long. It is constructed with thick insulation for long service life and a strong two-prong plug. This cord is compatible with the tools listed below. It can work for other applications and for other tools as well, but compatibility is not guaranteed. Installation of this part requires the new cord wires be stripped and to fit correctly into the wire terminals.

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

★★★★★

★★★★★

1 Review

Fix Number

FIX11929697

Manufacturer Part Number

N353819

This is an original replacement part manufactured for use with DeWalt angle grinders. This two wire cord had a rubberized jacket, and the wires have crimped terminals to make installation easier. The cordset is available individually.

Fix Number

FIX17061542

Manufacturer Part Number

N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Fix Number

FIX10153834

Manufacturer Part Number

664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

★★★★★

★★★★★

1 Review

Fix Number

FIX10153842

Manufacturer Part Number

664265-4

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Fix Number

FIX10169913

Manufacturer Part Number

330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Fix Number

FIX10153852

Manufacturer Part Number

664463-0

This power cord includes 2 prongs, 2 wires, and the gauge is 14. The measurement is 8 feet long and the type is bare wire. The cord is used on various power tools, specifically gardening and lawn equipment. With use and time, power tool cords can become frayed. If there are visible signs of wear on your cord, it is important to replace it immediately. For safety practices and installation instructions, refer to the diagram provided by the manufacturer.

Fix Number

FIX10169655

Manufacturer Part Number

330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Fix Number

FIX10131782

Manufacturer Part Number

44-76-0210

This cord protector is created to slide onto your cord and fit tightly at the end to protect the base of the cord from getting damaged. If the wires are exposed it can a be a safety hazard, so make sure to replace your cord protector if damaged. Refer to the manual provided by the manufacturer for further installation instructions.