OEM Black and Decker Angle Grinder Parts & Accessories

Power Cord

$35.31

Fix Number: FIX10169913
Manufacturer Part Number: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Ball Bearing

$6.51

Fix Number: FIX10188863
Manufacturer Part Number: N175104

This authentic replacement part is designed for use with DeWALT angle grinders. Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Bearings experience constant wear from pressure, heat, vibration, and friction eventually requiring replacements. This high-quality component is made of durable metal and is sold individually. A wrench set will be needed to perform this repair. Make sure to refer to the appropriate diagrams for your model to ensure the proper replacement procedure.

Carbon Brush

$13.36

Fix Number: FIX10183737
Manufacturer Part Number: 650918-01

This is a genuine Dewalt replacement part, it is sold individually. Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Terminal

$6.51

Fix Number: FIX10173813
Manufacturer Part Number: 464228-00

This is a terminal for your power tools. The terminal attaches to the cord of your machine, and then to the electrical connection on the tool. Through this connection, the electricity travels from the wall, through the terminal, and into your machine. The most common reason for needing to replace this part, is if your machine is plugged in but not turning on.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Watch the install video

Power Cord

$23.86

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Ball Bearing

$8.28

Fix Number: FIX10180907
Manufacturer Part Number: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

Carbon Brush With Spring

$10.77

Fix Number: FIX10173724
Manufacturer Part Number: 450374-12

This is a brush and spring for your power tools. This brush is sold individually, and two are needed for most power tools. We recommend replacing both brushes together for an even wear. When your brush wears down it will greatly affect your motor function by reducing the power and electric braking. When making this repair we recommend inspecting the armature for cracks or visible damage that would mean other motor problems. Carbon brushes are the most commonly replaced power tool part. This part is meant to wear out over time through the constant contact.

Cord Protector

$6.51

Fix Number: FIX17061542
Manufacturer Part Number: N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Watch the install video

Arm

$6.51

Fix Number: FIX10183642
Manufacturer Part Number: 648743-00

This is a single OEM brush arm. Your tool has two of these in total, but they are sold separately. The function of this part is to hold the brush in place against the armature. It also provides a place for the brush spring to sit, which puts tension against the armature. This part can fail if the tool gets overloaded, which may cause some melting. Once your tool has been disassembled, slide the brush arm onto the post and secure it with a screw, then re-install the brush and fold the arm back against the armature. Reinstall the brush wire and make sure the spring is placed onto the brush arm, then reassemble the tool housing back together. Very simple repair that should only take a few minutes.

Black and Decker Angle Grinder Parts

Popular Black and Decker Angle Grinder Parts

Installation Instructions

Installation Instructions

Black and Decker Angle Grinder Appliance Types

Related Black and Decker Angle Grinder Parts

Popular Black and Decker Angle Grinder Models

Black and Decker Angle Grinder Parts

Start With Your Model Number

Popular Black and Decker Angle Grinder Parts

Installation Instructions

Installation Instructions

Black and Decker Angle Grinder Appliance Types

Related Black and Decker Angle Grinder Parts

Popular Black and Decker Angle Grinder Models