OEM Delta Band Saw Parts & Accessories

Band Saw Table Insert

$12.45

Fix Number: FIX10323790
Manufacturer Part Number: 426020630001S

This is a table insert plate for your saw. It is attached to the table, and provides access to the blade. A table insert protects the rest of the unit by preventing wood from getting jammed under the blade during cutting. The slit in the insert plate allows for the saw blade to run smoothly. Before installing this part, unplug your saw.

Bearing

$54.95

Fix Number: FIX10315390
Manufacturer Part Number: 1086894S

This ball bearing fits a variety of lawn and gardening tools. The ball bearings prevent friction between rotating parts. The balls do this by bearing the load and spin and distributing the weight equally, while the minimal contact area of the balls reduce friction. This allows your tool to run easily. Ball bearings are a commonly replaced part because of the constant wear they experience. Tip: check your bearings and replace them periodically. *Please note: they are sold individually.

Tire

$9.85

Fix Number: FIX10322477
Manufacturer Part Number: 419960940002

Genuine Delta Polyurethane Upper Wheel Tire for 16" Bandsaw. When putting the tire on a band saw Wheel, it may seem too small but it is not. Band saw Tires will typically come approximately 2 or more inches smaller than the Tire you're replacing. The old Tire stretches over time thus becoming less effective and eventually will break. Also, as Tire ages the rubber hardens and allows the Blade to slip. You would need to put the New Tire in Hot/Warm Water to heat the tire enough to make it pliable enough to stretch. Its preferred to use two people in the stretching process.

Hinge

$39.55

Fix Number: FIX10328602
Manufacturer Part Number: 905153

This hinge has been OEM sourced to make certain of a high-quality standard. The metal hinge is intended to be used with Delta band saws. The hinge is used to mount and support the adjustment sliding bracket. This item is available as an individual replacement part.

Switch

$137.50

Fix Number: FIX10328665
Manufacturer Part Number: 905224

This is a switch for a variety of power tools. It is a commonly replaced part as it handles the on and off operations in your tool. This part will get damage over time because it uses mechanical internals. The most common reason for needing to replace the switch is if your tool has power but is not turning on.

Table Insert

$6.51

Fix Number: FIX10331503
Manufacturer Part Number: DPEC001462

Trunnion

$13.89

★★★★★

3 Reviews

Fix Number: FIX10323810
Manufacturer Part Number: 426020950002S

A genuine Delta replacement part, sold individually. A trunnion is a cylindrical protrusion used as a mounting and/or pivoting point. Held in place by three Cap Screws (901027631530), this part is compatible with the band saws listed below. A wrench is needed for repair.

Installation Instructions

Kenny from LAYTON, UT

Broken trunnions when trying to move bandsaw by lifting on table, not a good practice!!

Remove broken trunnions, fit new ones into place and tighten. Then mount on saw and if movements are hard or impossible, remove table top, and trunnions , and using a bench grinder remove molding marks from bolt retainers inside of trunnions. (Be careful not to let the grinder take the brackets out of your hands). Reassemble and try again. Read more...

Key

$11.79

Fix Number: FIX10318424
Manufacturer Part Number: 1343758

This safety key fits multiple hardware tools and is inserted into the switch to make it possible for your machine to turn on and operate. Tip: you can remove the key to prevent unauthorized use of the machine. For installation instructions refer to the diagram provided by the manufacturer.

Bearing

$6.51

Fix Number: FIX10331441
Manufacturer Part Number: DPEC001399

Push-button Switch

$43.95

Fix Number: FIX10328372
Manufacturer Part Number: 904121

This is a Genuine OEM Sourced replacement part used on Delta Power Equipment. This switch has a Plastic Body. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. Please note the Switch Box and the Cover are Sold Separately. To replace this switch you would need a Screwdriver. • First make sure the tools is not plugged in • Then you want to remove Screws used to hold two pieces of Housing Set together • Disconnect Wires from the old Switch and remove it from the Housing • Place the new Switch in the Housing and connect Wires to it • Reassembly the Housing

Delta Band Saw Parts

Popular Delta Band Saw Parts

Installation Instructions

Delta Band Saw Appliance Types

Related Delta Band Saw Parts

Popular Delta Band Saw Models

Delta Band Saw Parts

Start With Your Model Number

Popular Delta Band Saw Parts

Installation Instructions

Delta Band Saw Appliance Types

Related Delta Band Saw Parts

Popular Delta Band Saw Models