Sander Polisher Power Cords

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Fix Number

FIX19516305

Manufacturer Part Number

3604460555

This cord is a genuine OEM replacement part and is sold individually. Power Cord Specifications: 2 Wires. 18 Gauge. 2 Prongs. 6-1/2 Feet Long. It is constructed with thick insulation for long service life and a strong two-prong plug. This cord is compatible with the tools listed below. It can work for other applications and for other tools as well, but compatibility is not guaranteed. Installation of this part requires the new cord wires be stripped and to fit correctly into the wire terminals.

Fix Number

FIX10153834

Manufacturer Part Number

664064-4

This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing your old cord, take note of the wire leads placements, and how they connect to the receptacle in the tool. You will have to attach the new cord similarly.

Fix Number

FIX10131782

Manufacturer Part Number

44-76-0210

This cord protector is created to slide onto your cord and fit tightly at the end to protect the base of the cord from getting damaged. If the wires are exposed it can a be a safety hazard, so make sure to replace your cord protector if damaged. Refer to the manual provided by the manufacturer for further installation instructions.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX10173396

Manufacturer Part Number

445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

Fix Number

FIX10153839

Manufacturer Part Number

664213-3

This cord is a genuine Makita replacement part and is sold individually. This cord is made for the double insulated tools shown below It is a two wire cord with two prongs and does not need a ground wire.

Fix Number

FIX10122674

Manufacturer Part Number

22-64-0215

This is a cord set for your power tools. It is constructed with a tough outer-rubber insulation for a longer life span. The 18-gauge power cord is 8 feet long, and comes with 2 prongs and 2 wires. This cord is black in color and is sold individually.

Fix Number

FIX12529262

Manufacturer Part Number

N380209

This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. rnPower Cord Specifications: rn • 3 Prongs rn • 3 Wires rn • 16 Gauge rn • 7 Feet Long

Fix Number

FIX18990674

Manufacturer Part Number

A11126

This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications 3 Prongs 3 Wires 18 Gauge 7 Feet Long

Fix Number

FIX10122663

Manufacturer Part Number

22-64-0121

This cord is a genuine Milwaukee replacement part and is sold individually. This cord is used on the Milwaukee tool listed below It is a 3 wire cord with 3 prongs and does need to be grounded to the tool.