Sander Polisher Seals and Gaskets

Fix Number

FIX10166528

Manufacturer Part Number

151553-00

Genuine OEM replacement part, this item is sold individually. The 151553-00 Dust Seal/Brake is a dual propose part. It is a Dust Seal to help prevent dust and debris from entering the motor assembly. It also acts as a Brake to keep the sanding pad at lower RPM so the sander will work properly. It is a good idea to replace this part when you are replacing the sanding pad.

Fix Number

FIX10166041

Manufacturer Part Number

144974-00

This is a genuine DeWALT replacement part to be used in sanders. The dust seal fits in the platen. It prevents dust from entering the device. This item is available as an individual replacement part, and may require a screwdriver to install.

Fix Number

FIX10179429

Manufacturer Part Number

56194-00

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-ring failure. The most common among power tools are: • The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the O-ring, or caused by clearance gaps. • One or both sides of the O-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit, or is too smooth to allow lubrication. • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding O-ring capacity. • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays, and air pollution. Excessive seal stretching (greater than 5%) causes similar cracking.

Fix Number

FIX10126953

Manufacturer Part Number

34-40-1870

This is an authentic manufacturer-sourced replacement component that is specially designed for use with Milwaukee sanders. It helps to provide an air-tight seal between connected parts, please make sure to refer to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.

Fix Number

FIX10336573

Manufacturer Part Number

01464

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.

Fix Number

FIX10141737

Manufacturer Part Number

213047-7

This is an authentic manufacturer-sourced replacement part, it is specially designed for use with Makita finishing sanders. Two of these o-rings are used to provide a strong seal for the foot, for correct application make sure to check appropriate diagrams of your model. Over time the o-rings may begin to deteriorate and crack eventually requiring replacement. It is a high-quality part which is made of durable rubber material and it is sold individually.

Fix Number

FIX10184200

Manufacturer Part Number

700871-00

This is an original DeWALT replacement part. The O-ring is designed by the manufacturer for use in random orbit sanders. This part is made of flexible rubber, and is used to seal the connection between the clamshell set and the baffle. You may require a screwdriver or Allen wrench when replacing this item. This part is sold individually.

Fix Number

FIX10127036

Manufacturer Part Number

34-40-4300

Included in part number 14-30-0302

Fix Number

FIX12455032

Manufacturer Part Number

801852

This is an authentic manufacturer sourced replacement seal that is commonly utilized on electric power tools. It has multiple uses depending on the equipment, for correct location and use of this hardware please make sure to check appropriate diagrams of your tool. Over time these seals tend to shrink, become brittle and crack eventually requiring replacement. Please note this durable rubber seal is sold individually.

Fix Number

FIX17754581

Manufacturer Part Number

339012430