OEM Black and Decker Sander Polisher Parts & Accessories

On-off Switch

$6.51

Fix Number: FIX10166039
Manufacturer Part Number: 144960-00

This part includes one on-off switch, also referred to as a rocker switch. This switch is an original manufacturer replacement part. The switch controls the flow of electricity to the motor, and when it wears it can make it impossible to start the power tool. Switches are a common replacement part for power tools, so it is something that should be inspected as part of your regular maintenance. This black switch has two terminals and a compact design for an uncomplicated installation process. To confirm that the switch is damaged, you can test it for continuity using a multimeter.

Switch

$6.51

Fix Number: FIX10183942
Manufacturer Part Number: 656494-00

Platen

$8.04

Fix Number: FIX10187979
Manufacturer Part Number: N073798

This is a genuine OEM replacement part, it is sold individually. This is the part of the sander that holds the foam pad that the sandpaper is placed against. It is made of plastic. It does not include the bearing, dust seal or paper clamps.

Watch the install video

Power Cord

$23.86

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

SA DUST BAG

$9.77

Fix Number: FIX18989159
Manufacturer Part Number: 90606681

Cord Protector

$7.89

★★★★★

3 Reviews

Fix Number: FIX10173396
Manufacturer Part Number: 445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

Watch the install video

Sander Pad & Backing Plate

$8.66

★★★★★

1 Review

Fix Number: FIX10166489
Manufacturer Part Number: 151284-00SV

This is an OEM sander pad and backing plate for a sander. It is most commonly replaced due to sudden uneven sanding or difficulty keeping the sandpaper properly attached. This part includes a steel plate with a foam pad fixed to it. The foam pad gives grip for the sandpaper to adhere firmly within the clamps. This foam material is prone to deteriorate over time, causing irregular sanding. If the pad is so worn that the metal plate is making contact with the paper, the sander will start to jump around. This is a very quick and easy repair. Simply remove the four screws holding the old pad in place, line up the the holes of the pad with the holes in the plate, and tighten the four screws back up (screws sold separately).

Sander Pad (hook And Loop)

$9.72

Fix Number: FIX17016197
Manufacturer Part Number: N601645

This replacement sander pad is specially produced for use with sanders. It is an authentic item supplied directly from original equipment manufacturer. This hook and loop fastener closure system allows for easy sandpaper application. The rough side would interlock with softer side making the closure mechanism. This part is made out of plastic material and it is sold individually. Please note screws to attach it are sold separately. Replacing this sander pad is very simple and quick task. You should only need a screwdriver. • Make sure the unit is unplugged • First remove the screws that secure the old pad • Remove the pad and replace it with the new one • Secure it using the screws and test the unit

Soft Mount

$15.42

Fix Number: FIX10173448
Manufacturer Part Number: 445928-01

The soft mount fits between the guard assembly and the gear case cover. It is an authentic OEM sourced item which is specifically produced for use with DeWALT and Black & Decker grinders and sanders. This high-quality part is sold individually and is made out of metal. A wrench set may be necessary to use while replacing this mount.

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Black and Decker Sander Polisher Parts

Popular Black and Decker Sander Polisher Parts

Installation Instructions

Black and Decker Sander Polisher Appliance Types

Popular Black and Decker Sander Polisher Models

Black and Decker Sander Polisher Parts

Start With Your Model Number

Popular Black and Decker Sander Polisher Parts

Installation Instructions

Black and Decker Sander Polisher Appliance Types

Popular Black and Decker Sander Polisher Models