OEM Ridgid Sander Polisher Parts & Accessories

SANDING DRUM

$6.51

Fix Number: FIX18686701
Manufacturer Part Number: 080038001438

This manufacturer approved replacement part is designed for use with Ridgid sanders. This sanding drum helps to support and drive the sandpaper. It is made out of rubber material and it is sold individually. To complete this repair you would need pliers.

WASHER 11/32X1 3/4X1/8

$6.51

Fix Number: FIX18701299
Manufacturer Part Number: 805553-30

This is an authentic Ridgid replacement part that has been sourced from the original manufacturer to be used with oscillating spindle and belt sanders. The washer is used to cover the top end of the larger spindle assembly. This item is sold as an individual replacement part.

WASHER 11/32X7/8X1/16

$6.51

Fix Number: FIX18701298
Manufacturer Part Number: 805553-24

This is an authentic Ridgid item, not an aftermarket imitation. It is sourced from original equipment manufacturer for use on circular saws and sanders. The purpose of a washer is to distribute the pressure evenly between two connected parts. For correct use and location of this washer please make sure to check appropriate diagrams. This part is made from durable metal and it is sold individually.

ASSEMBLY SPRING CLAMP

$6.51

Fix Number: FIX18693911
Manufacturer Part Number: 303614004

Genuine Manufacturer Approved replacement part used on Ridigd Sheet Sander. This part is made out of Metal and it has a Plastic Handle. This item is Sold Individually. This Clamp helps to secure the sandpaper to the Plate.

BRUSH ASSEMBLY

$6.51

Fix Number: FIX18693549
Manufacturer Part Number: 290255001

This replacement carbon brush is a genuine OEM sourced replacement part designed for use with a variety of power tools. This assembly includes one (1) carbon brush with a lead wire and a spring attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the brush caps • Take our old brushes and replace them with the new ones • Secure brush caps and test the tool

BRAKE SKIRT

$6.51

Fix Number: FIX18726545
Manufacturer Part Number: 590936005

This is an OEM brake skirt for a random orbit sander, sold individually. The brake is located just above the pad. It rubs against the pad and prevents it from rotating when the sander is not touching the workpiece. Over the use of the tool, the brake skirt will wear out eventually. It will become evident that it is worn if the pad is rotating at a high RPM when the sander is not on the workpiece. This can cause a gouge when the sander first contacts the workpiece.

5 DISC ASSEMBLY W/ H&L

$8.75

★★★★★

1 Review

Fix Number: FIX18693700
Manufacturer Part Number: 300527002

This is an authentic 5-inch sanding pad assembly for a sander. It provides support for hook and loop sandpaper. This part is prone to deteriorate, especially if too much pressure is applied to the sander while in use. This creates too much heat, which wears the sanding pad much quicker. For this simple repair, unfasten the four screws attaching the pad to the sander, and fasten the new pad in its place. This OEM pad assembly is sold individually.

Installation Instructions

Michael from EL PASO, TX

replaced hook and loop pad

Removed the 4 screws and replaced. Read more...

Ball Bearing (6000lu)

$6.40

Fix Number: FIX9868401
Manufacturer Part Number: 039176001012

It is an original manufacturer supplied replacement item and is sold individually. This ball bearing is sealed on both sides. Ball bearings are made to reduce friction between two rotating parts. Because they experience constant pressure they would need to be checked and replaced periodically to ensure top performance. Please check diagrams for correct location and application of this bearing.

SPINDLE KNOB

$7.70

★★★★★

3 Reviews

Fix Number: FIX18686700
Manufacturer Part Number: 080038001436

This part is an OEM part from Ridgid for use on a spindle sander. The purpose of the spindle knob is to lock the sanding drum and sanding belt assembly in place. This spindle knob has left-hand threads to loosen the knob turn it clockwise and to tighten turn counter-clockwise. The knob itself is made of a durable plastic with a metal shaft. This item is sold as an individual replacement part.

Tile Saw Ball Bearing

$6.51

Fix Number: FIX9995584
Manufacturer Part Number: 671498001

Ridgid Sander Polisher Parts

Popular Ridgid Sander Polisher Parts

Installation Instructions

Ridgid Sander Polisher Appliance Types

Related Ridgid Sander Polisher Parts

Popular Ridgid Sander Polisher Models

Ridgid Sander Polisher Parts

Start With Your Model Number

Popular Ridgid Sander Polisher Parts

Installation Instructions

Ridgid Sander Polisher Appliance Types

Related Ridgid Sander Polisher Parts

Popular Ridgid Sander Polisher Models