Sander Polisher Brackets and Flanges

Popular Sander Polisher Brackets and Flanges

Steel Plate
$10.36
In Stock
Fix Number
FIX10148825
Manufacturer Part Number
344620-3
This is a Genuine Manufacturer Sourced replacement part designed for use with Makita Belt Sander. It is Made out of Metal and it is Sold Individually. Due to constant contact, pressure and vibration this part should be inspected periodically and replaced if showing signs of wear to ensure optimum performance. When replacing Steel Plate it is advised to inspect the Cork Plate and replace it if it shows signs of wear. To replace this part you will need a Screwdriver. • Unscrew the Steel Plate that is being held by Three (3) Pan Head Screws. • Once it is removed simply replace it with the new one • Reattach it using the same Three (3) screws. Please note Cork Plate and Screws are Sold Separately.
★★★★★
★★★★★
1 Review
Fix Number
FIX10156640
Manufacturer Part Number
CB124
Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.
Steel Plate
$16.95
In Stock
Fix Number
FIX10139344
Manufacturer Part Number
151749-6
This replacement steel plate is a genuine Makita item, not an aftermarket imitation. It is specially designed for use with belt sanders. This assembly consists of a steel plate that helps to support the sandpaper and a cork backing to reduce the vibration. Over time this plate will wear out requiring replacement. Please note, this item is sold individually. The hardware to secure this steel plate is sold separately. To replace this part you will need a screwdriver. • Make sure the sander is unplugged • Unscrew the steel plate • Secure the new plate in place
Steel Plate
$11.20
In Stock
Fix Number
FIX10148340
Manufacturer Part Number
341705-6
This steel plate is an authentic Makita replacement part. It is made specifically for the Makita 9924DB Belt Sander. This plate simply provides a durable surface for the sandpaper to push against during sanding. It should be replaced if it is worn or damaged. The installation for this part is straightforward and should only take a few minutes. A screwdriver is needed to remove and re-install the two screws holding the plate in place.
Steel Plate
$23.48
In Stock
Fix Number
FIX10139346
Manufacturer Part Number
151751-9
This is a high quality replacement part designed for a Makita belt sander. It is an authentic item sourced directly from original equipment manufacturer. When replacing this steel plate it is advised to inspect the cork plate which is sold separately and replace it if shows signs of wear. Please note, this item is sold individually. To replace this steel plate you will need a screwdriver.
Flange
$6.51
On Order
Fix Number
FIX10134064
Manufacturer Part Number
49-05-0041
This is an Original replacement part used on certain Milwaukee Angle Grinders. This part is made out of Metal and it is Sold Individually. The purpose of this Flange is to hold the Grinding Wheel to the Spindle Shaft. Flange designed to accommodate 7/8 In. hub depressed center wheel.
Bearing Retainer
$6.51
In Stock
Fix Number
FIX10180809
Manufacturer Part Number
603664-00
This authentic item is supplied by the original manufacturer for DeWALT random orbit sanders. It is the bottom half of the bearing retainer which is utilized to secure the armature bearing. The part is secured three screws which also attach the sanding pad. Note, the hardware is sold separately. It provides a high-quality replacement for a missing or a damaged part that was installed on a new unit. Make sure to refer to the owner's manual and the diagrams of your model for the correct installation of this component. You will need a screwdriver to perform this repair.
Steel Plate
$20.06
In Stock
Fix Number
FIX10139345
Manufacturer Part Number
151750-1
This replacement steel plate is a high quality item that is specially designed for Makita belt sanders. Due to constant contact, pressure and vibration this part should be inspected periodically and replaced if showing signs of wear to ensure optimum performance. Please note one durable steel plate is included per order, to replace this part you will need a screwdriver.
PLATE STOP
$10.75
In Stock
Fix Number
FIX18686693
Manufacturer Part Number
080038001427
Front End Plate Assembly
$70.16
In Stock
Fix Number
FIX12095906
Manufacturer Part Number
313A-A11

Sander Polisher Bracket or Flange Brands