Makita Sander Polisher Brackets and Flanges

Makita Appliance Parts

Popular Makita Sander Polisher Brackets and Flanges

Steel Plate
$10.36
In Stock
Fix Number
FIX10148825
Manufacturer Part Number
344620-3
This is a Genuine Manufacturer Sourced replacement part designed for use with Makita Belt Sander. It is Made out of Metal and it is Sold Individually. Due to constant contact, pressure and vibration this part should be inspected periodically and replaced if showing signs of wear to ensure optimum performance. When replacing Steel Plate it is advised to inspect the Cork Plate and replace it if it shows signs of wear. To replace this part you will need a Screwdriver. • Unscrew the Steel Plate that is being held by Three (3) Pan Head Screws. • Once it is removed simply replace it with the new one • Reattach it using the same Three (3) screws. Please note Cork Plate and Screws are Sold Separately.
★★★★★
★★★★★
1 Review
Fix Number
FIX10156640
Manufacturer Part Number
CB124
Carbon brushes are needed to conduct electricity to the armature through the commutator. The brushes are continuously rubbing against the rotating commutator, so will wear down over time, and will need to be replaced. If you are experiencing excessive sparks, this can also be caused by a damaged armature, so it is best to check it at the same time. This part includes two carbon brushes, which need to be replaced at the same time.
Steel Plate
$16.95
In Stock
Fix Number
FIX10139344
Manufacturer Part Number
151749-6
This replacement steel plate is a genuine Makita item, not an aftermarket imitation. It is specially designed for use with belt sanders. This assembly consists of a steel plate that helps to support the sandpaper and a cork backing to reduce the vibration. Over time this plate will wear out requiring replacement. Please note, this item is sold individually. The hardware to secure this steel plate is sold separately. To replace this part you will need a screwdriver. • Make sure the sander is unplugged • Unscrew the steel plate • Secure the new plate in place
Steel Plate
$11.20
In Stock
Fix Number
FIX10148340
Manufacturer Part Number
341705-6
This steel plate is an authentic Makita replacement part. It is made specifically for the Makita 9924DB Belt Sander. This plate simply provides a durable surface for the sandpaper to push against during sanding. It should be replaced if it is worn or damaged. The installation for this part is straightforward and should only take a few minutes. A screwdriver is needed to remove and re-install the two screws holding the plate in place.
Steel Plate
$23.48
In Stock
Fix Number
FIX10139346
Manufacturer Part Number
151751-9
This is a high quality replacement part designed for a Makita belt sander. It is an authentic item sourced directly from original equipment manufacturer. When replacing this steel plate it is advised to inspect the cork plate which is sold separately and replace it if shows signs of wear. Please note, this item is sold individually. To replace this steel plate you will need a screwdriver.
Steel Plate
$20.06
In Stock
Fix Number
FIX10139345
Manufacturer Part Number
151750-1
This replacement steel plate is a high quality item that is specially designed for Makita belt sanders. Due to constant contact, pressure and vibration this part should be inspected periodically and replaced if showing signs of wear to ensure optimum performance. Please note one durable steel plate is included per order, to replace this part you will need a screwdriver.
Bracket
$42.65
In Stock
Fix Number
FIX10146905
Manufacturer Part Number
317523-4
Base Plate
$19.32
In Stock
Fix Number
FIX10148333
Manufacturer Part Number
341647-4
This is a genuine Makita replacement part that has been sourced from the original manufacturer and is intended to be used with portable belt sanders. The base plate attaches to the sander's frame. This item is used to support the backing plates to allow the sanding belt to be pressed against the material being sanded. The base plate is sold as an individual item.
Dust Collector Bracket
$32.21
In Stock
Fix Number
FIX10146812
Manufacturer Part Number
317021-8
Steel Plate
$6.19
In Stock
Fix Number
FIX10148811
Manufacturer Part Number
344586-7
This replacement part has been directly sourced from the Makita manufacturer. The steel plate is compatible with the 9910 and 9911 belt sanders. The plate is secured onto the bottom of the sander shoe, providing a smooth surface for the sandpaper belt. It is recommended to always use the correct steel plate for best performance of the sander and abrasives. This item is sold individually. A screwdriver is needed for the repair.

Related Makita Sander Polisher Parts