OEM Craftsman Impact Driver Parts & Accessories

Compression Spring

$6.51

Fix Number: FIX11929265
Manufacturer Part Number: N019351

The compression spring is part of the impact drivers chuck assembly. The spring is found over the anvil shaft and provides tension to pull the chuck collar back after a bit is removed. Over time this part can lose tension or become damaged. A failed compression spring will cause the collar to move freely, and the driver bit will come loose. This is an OEM official part and is sold individually.

Carbon Brush With Spring

$10.77

Fix Number: FIX10173724
Manufacturer Part Number: 450374-12

This is a brush and spring for your power tools. This brush is sold individually, and two are needed for most power tools. We recommend replacing both brushes together for an even wear. When your brush wears down it will greatly affect your motor function by reducing the power and electric braking. When making this repair we recommend inspecting the armature for cracks or visible damage that would mean other motor problems. Carbon brushes are the most commonly replaced power tool part. This part is meant to wear out over time through the constant contact.

Carbon Brush With Lead

$9.08

Fix Number: FIX10183918
Manufacturer Part Number: 655213-02

This part includes one carbon brush with wire lead in attached rubber sheath. Your tool will have two carbon brushes, so it is a good idea to inspect both and replace them at the same time. This carbon brush is compatible with various types of tools, such as drills, impact drivers, and impact wrenches, to name a few. This carbon brush is sourced directly from the manufacturer, ensuring the proper fit with your equipment. It is most commonly replaced due to a poorly performing engine, and is a common wear part that should be checked regularly.

RETAINING RING

$6.51

Fix Number: FIX12529368
Manufacturer Part Number: N421245

Keep your impact driver or drill operating reliably with this retaining ring, a small but essential component that helps secure internal chuck and bit-retention parts in place. By preventing unwanted movement of key components, it helps maintain proper bit retention and consistent power transfer during operation. A worn, bent, or damaged retaining ring can lead to loose components, bit wobble, or retention issues, making replacement an important repair. Because retaining ring locations and sizes can vary between models, refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

Spring

$6.51

Fix Number: FIX12527474
Manufacturer Part Number: N437890

This is an OEM authorized spring for an impact driver. It is sold individually. It is part of the bit holder assembly and works with other components to create pressure on the sleeve, helping to keep the bit in the holder. If this spring gets lost or stretches, it will need to be replaced. It has an approximate outside diameter of 0.545-inches, and the wire is about 0.030-inches.

Power Cord (8-foot)

$29.79

Fix Number: FIX10169907
Manufacturer Part Number: 330077-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 8 Feet Long

Hog Ring

$6.51

Fix Number: FIX12533153
Manufacturer Part Number: N424032

This genuine OEM hog ring is used in impact drivers. It is a thick, circular wire with a diameter of 0.5 inches. It is positioned around the output shaft where it grips and secures the socket or adapter. Over time, the hog ring may corrode, break, or lose tension leading to socket instability. To remove a faulty hog ring, use needle-nose pliers or a small flat-head screwdriver to carefully pry it out of the mounting groove around the output shaft. Slide a new hog ring in the empty space until it locks into place. Inspect all the hog rings in your equipment and replace all those that are no longer functional. Each hog ring is sold individually.

Detent Pin

$6.51

Fix Number: FIX10187196
Manufacturer Part Number: N020802

This is a genuine Dewalt replacement part, it is sold individually. The purpose of the Detent Pin is to secure sockets to the anvil on the Impact Wrench model numbers shown below. It is held in the anvil by use of a spring and pin.

Anvil Assembly

$20.18

Fix Number: FIX12523150
Manufacturer Part Number: N439275

Keep your impact driver performing at its best with this anvil assembly, the component that securely holds 1/4 in. hex bits and transfers torque from the impact mechanism to the fastener. Made from durable steel for long-lasting performance, it helps ensure reliable bit retention and smooth power delivery during demanding applications. A worn, damaged, or wobbling anvil can affect fastening performance and bit stability, making replacement an effective way to restore proper operation. Refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

Washer - Urethane

$6.51

Fix Number: FIX11928144
Manufacturer Part Number: 642883-00

This is an authentic OEM part used in DeWALT and Porter Cable impact drivers. It fits between the anvil assembly and the sleeve. If it becomes lost or broken it will need replacing and a screwdriver may be needed during the installation. This part is made of urethane, a hard plastic, and is available individually.

Craftsman Impact Driver Parts

Popular Craftsman Impact Driver Parts

Craftsman Impact Driver Appliance Types

Popular Craftsman Impact Driver Models

Craftsman Impact Driver Parts

Start With Your Model Number

Popular Craftsman Impact Driver Parts

Craftsman Impact Driver Appliance Types

Popular Craftsman Impact Driver Models