OEM Craftsman Cordless Drill Parts & Accessories

Handle,spade

$13.87

Fix Number: FIX10182689
Manufacturer Part Number: 628037-00

This is an original replacement part manufactured for use with drills. This hardened plastic spade handle is secured at the back of the drill using a knob, which is available separately. The spade handle provides an additional grip option for heavy duty drills, please note the spade handle is sold individually.

Steel Ball

$6.51

Fix Number: FIX11929439
Manufacturer Part Number: N089668

The steel ball is part of the bit holder in an impact driver and is sold individually. The driver bit is held securely by the ball, which fits into the spindle. The ball is attached to the spindle by the collar. Over time, the collar can come loose, and the ball could get lost. The ball itself can sometimes wear, causing the driver to become loose rather easily. To access this part, you will need to remove the hog ring, which fits into a groove on the anvil. When removing this part, be careful not to misplace parts, as there is a spring behind the hog ring, which will become loose. This will allow you to remove the collar and steel ball. Remove the ball using a magnet, to keep it contained.

Spring

$6.51

Fix Number: FIX12527474
Manufacturer Part Number: N437890

This is an OEM authorized spring for an impact driver. It is sold individually. It is part of the bit holder assembly and works with other components to create pressure on the sleeve, helping to keep the bit in the holder. If this spring gets lost or stretches, it will need to be replaced. It has an approximate outside diameter of 0.545-inches, and the wire is about 0.030-inches.

Anvil Assembly

$20.18

Fix Number: FIX12523150
Manufacturer Part Number: N439275

Strong fastening depends on the anvil holding the driver bit securely while carrying each impact to the screw or bolt. Wear or damage may cause poor bit retention, excess movement, noise, or reduced power. Test with an undamaged bit and inspect the chuck parts before ordering a replacement. Match the assembly to the full tool model and service diagram. Disconnect the battery, wear eye protection around spring clips, use only the approved lubricant, and test the repaired tool at low speed first.

Washer - Urethane

$6.51

Fix Number: FIX11928144
Manufacturer Part Number: 642883-00

This is an authentic OEM part used in DeWALT and Porter Cable impact drivers. It fits between the anvil assembly and the sleeve. If it becomes lost or broken it will need replacing and a screwdriver may be needed during the installation. This part is made of urethane, a hard plastic, and is available individually.

Carbon Brush

$9.06

Fix Number: FIX10172207
Manufacturer Part Number: 400814-00

Genuine Dewalt/Black & Decker replacement part. includes 1 Carbon Brush with wire lead and brush spring attached. 2 Brushes are needed for the tools listed below. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Watch the install video

Keyless Chuck

$47.25

Fix Number: FIX10188921
Manufacturer Part Number: N196034

This genuine replacement keyless drill chuck is designed for quick, tool-free bit changes and reliable performance during demanding drilling and driving tasks. Built with a durable metal construction and an automatic locking mechanism, it provides a strong grip to help minimize bit slippage, even in high-torque applications. The chuck supports a wide range of bit sizes and installs directly onto the drill spindle, making it an effective solution for restoring accuracy, stability, and ease of use when an existing chuck is worn or damaged.

RETAINING RING

$6.51

Fix Number: FIX12529368
Manufacturer Part Number: N421245

Keep your impact driver or drill operating reliably with this retaining ring, a small but essential component that helps secure internal chuck and bit-retention parts in place. By preventing unwanted movement of key components, it helps maintain proper bit retention and consistent power transfer during operation. A worn, bent, or damaged retaining ring can lead to loose components, bit wobble, or retention issues, making replacement an important repair. Because retaining ring locations and sizes can vary between models, refer to your tool's parts diagram or service manual to confirm the correct application before installation. Sold individually.

Hog Ring

$6.51

Fix Number: FIX12533153
Manufacturer Part Number: N424032

This genuine OEM hog ring is used in impact drivers. It is a thick, circular wire with a diameter of 0.5 inches. It is positioned around the output shaft where it grips and secures the socket or adapter. Over time, the hog ring may corrode, break, or lose tension leading to socket instability. To remove a faulty hog ring, use needle-nose pliers or a small flat-head screwdriver to carefully pry it out of the mounting groove around the output shaft. Slide a new hog ring in the empty space until it locks into place. Inspect all the hog rings in your equipment and replace all those that are no longer functional. Each hog ring is sold individually.

Compression Spring

$6.51

Fix Number: FIX11929265
Manufacturer Part Number: N019351

The compression spring is part of the impact drivers chuck assembly. The spring is found over the anvil shaft and provides tension to pull the chuck collar back after a bit is removed. Over time this part can lose tension or become damaged. A failed compression spring will cause the collar to move freely, and the driver bit will come loose. This is an OEM official part and is sold individually.

Craftsman Cordless Drill Parts

Popular Craftsman Cordless Drill Parts

Craftsman Cordless Drill Appliance Types

Related Craftsman Cordless Drill Parts

Popular Craftsman Cordless Drill Models

Craftsman Cordless Drill Parts

Start With Your Model Number

Popular Craftsman Cordless Drill Parts

Craftsman Cordless Drill Appliance Types

Related Craftsman Cordless Drill Parts

Popular Craftsman Cordless Drill Models