OEM Craftsman Orbital or Palm Sander Parts & Accessories

Sander Base Plate

$39.64

Fix Number: FIX12533027
Manufacturer Part Number: N329079

This genuine OEM pad assembly—also known as a hook-and-loop sanding pad or sanding disc—is designed for use with compatible sanders and sourced directly from the original manufacturer. The circular pad measures 4.75 inches in diameter, features 8 dust extraction holes, and includes a Velcro backing to securely hold sandpaper discs in place during operation. Mounted to the base of the sander, this pad allows for smooth, efficient sanding and consistent surface finishing. Over time, the Velcro surface may wear down, or the pad may become cracked or stripped, leading to poor sandpaper grip, uneven sanding, or reduced performance. Replacing the pad is a simple repair that requires no specialized tools. To install, use a screwdriver to remove the retaining screws from the old pad. Align the new pad assembly with the mounting holes and secure it using the original or replacement screws. It’s recommended to inspect and replace any stripped or corroded screws during installation for best results. This part is sold individually and is ideal for restoring your sander’s performance and extending its service life.

Pulley

$6.51

Fix Number: FIX16687699
Manufacturer Part Number: N544253

Pad Assembly (psa)

$19.96

Fix Number: FIX12525699
Manufacturer Part Number: N373679

This is a single pad assembly for a random orbit sander. The pad assembly holds the sand paper in place and creates a level surface needed for sanding. Pads are prone to wear and tare over time and will need to be replaced when they do. It will start to deteriorate around the edge. To prolong the life of your pad assembly do not apply too much pressure to the pad while sanding. This simple repair should only take a few minutes to complete.

5 DISC ASSEMBLY W/ H&L

$8.75

★★★★★

1 Review

Fix Number: FIX18693700
Manufacturer Part Number: 300527002

This is an authentic 5-inch sanding pad assembly for a sander. It provides support for hook and loop sandpaper. This part is prone to deteriorate, especially if too much pressure is applied to the sander while in use. This creates too much heat, which wears the sanding pad much quicker. For this simple repair, unfasten the four screws attaching the pad to the sander, and fasten the new pad in its place. This OEM pad assembly is sold individually.

Installation Instructions

Michael from EL PASO, TX

replaced hook and loop pad

Removed the 4 screws and replaced. Read more...

Cord Protector

$6.51

Fix Number: FIX17061542
Manufacturer Part Number: N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Retainer-end Cap

$6.51

Fix Number: FIX12522657
Manufacturer Part Number: N329083

POWER CORD

$16.85

Fix Number: FIX12523044
Manufacturer Part Number: N389354

Switch

$6.51

Fix Number: FIX10183942
Manufacturer Part Number: 656494-00

Dust Bag Assembly

$11.00

Fix Number: FIX12522964
Manufacturer Part Number: N273733

This authentic OEM dust bag assembly is sourced from the original manufacturer for use in sanders. It consists of a fabric bag and plastic cap measuring approximately 5.5 inches in length and 2.5 inches in diameter. The bag assembly collects the dust and debris that is produced during sanding allowing you to maintain a clean and safe working environment. Over time the bag may tear or wear down, leading to large amounts of dust escaping into the air, health hazards from dust inhalation, reduction in visibility, and a messy work area. Replacing the dust bag assembly is a simple repair that does not require the use of specialized tools. Simply detach the bag from the sander, remove any dust and debris on the mounting surface, and attach the new bag.

Ball Bearing

$8.28

Fix Number: FIX10180907
Manufacturer Part Number: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

Craftsman Orbital or Palm Sander Parts

Popular Craftsman Orbital or Palm Sander Parts

Installation Instructions

Craftsman Orbital or Palm Sander Appliance Types

Popular Craftsman Orbital or Palm Sander Models

Craftsman Orbital or Palm Sander Parts

Start With Your Model Number

Popular Craftsman Orbital or Palm Sander Parts

Installation Instructions

Craftsman Orbital or Palm Sander Appliance Types

Popular Craftsman Orbital or Palm Sander Models