Orbital or Palm Sander Parts

Sander Base Plate

$39.64

Fix Number: FIX12533027
Manufacturer Part Number: N329079

This genuine OEM pad assembly—also known as a hook-and-loop sanding pad or sanding disc—is designed for use with compatible sanders and sourced directly from the original manufacturer. The circular pad measures 4.75 inches in diameter, features 8 dust extraction holes, and includes a Velcro backing to securely hold sandpaper discs in place during operation. Mounted to the base of the sander, this pad allows for smooth, efficient sanding and consistent surface finishing. Over time, the Velcro surface may wear down, or the pad may become cracked or stripped, leading to poor sandpaper grip, uneven sanding, or reduced performance. Replacing the pad is a simple repair that requires no specialized tools. To install, use a screwdriver to remove the retaining screws from the old pad. Align the new pad assembly with the mounting holes and secure it using the original or replacement screws. It’s recommended to inspect and replace any stripped or corroded screws during installation for best results. This part is sold individually and is ideal for restoring your sander’s performance and extending its service life.

Cord Protector

$6.51

Fix Number: FIX17061542
Manufacturer Part Number: N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Hook And Loop Sander Pad

$10.88

★★★★★

1 Review

Fix Number: FIX11878741
Manufacturer Part Number: 51-36-7100

This is a genuinely sourced hook and loop sander pad for your sander. It is intended for 5-inch discs, and has 8 dust collection holes, which work alongside the dust bag to contain debris. Be careful not to apply too much tension on the sander as this can lead to early wear on the hook and loop sander pad. When replacing a pad, remove the four screws that secure the pad to the sander and replace it with your new pad.

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Pad Assembly (psa)

$19.96

Fix Number: FIX12525699
Manufacturer Part Number: N373679

This is a single pad assembly for a random orbit sander. The pad assembly holds the sand paper in place and creates a level surface needed for sanding. Pads are prone to wear and tare over time and will need to be replaced when they do. It will start to deteriorate around the edge. To prolong the life of your pad assembly do not apply too much pressure to the pad while sanding. This simple repair should only take a few minutes to complete.

Belt

$7.27

Fix Number: FIX12529381
Manufacturer Part Number: N430442

This part includes a single belt for a random orbital sander. It is located between the pad and the sander body. It helps to control the pad speed while the tool is off the work surface. The belt is a common wear part that will require replacement from time to time (along with the pad, which is sold separately). The belt should be replaced when the pad speed increase significantly when the unit is removed from the work piece. For this repair, remove the screws holding the pad in place, remove the pad, replace the damaged belt by wrapping it around the shoulder screw and bearing retainer. Reinstall the pad and re-tighten the screws, being careful not to over-tighten them.

5 DISC ASSEMBLY W/ H&L

$8.75

★★★★★

1 Review

Fix Number: FIX18693700
Manufacturer Part Number: 300527002

This is an authentic 5-inch sanding pad assembly for a sander. It provides support for hook and loop sandpaper. This part is prone to deteriorate, especially if too much pressure is applied to the sander while in use. This creates too much heat, which wears the sanding pad much quicker. For this simple repair, unfasten the four screws attaching the pad to the sander, and fasten the new pad in its place. This OEM pad assembly is sold individually.

Installation Instructions

Michael from EL PASO, TX

replaced hook and loop pad

Removed the 4 screws and replaced. Read more...

PAD

$35.15

Fix Number: FIX12398026
Manufacturer Part Number: 151281-08

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Brush Box Asm

$6.51

Fix Number: FIX12522639
Manufacturer Part Number: N292059

This is a brush box assembly designed for various sander models. Brush boxes are essential components that house carbon brushes responsible for transferring electricity from the motor to the sanding pad. When the carbon brush assembly wears out, it can no longer efficiently transfer electricity, causing the sander to stop working. This brush box assembly includes the carbon brush, its housing, and the necessary wiring. Replacing the brush box assembly is a straightforward process, requiring only a screwdriver and a set of pliers. Begin by disconnecting your sander from its power source, whether it is a battery or a wall outlet. Next, remove the screws securing the main housing of the sander and locate the brushes inside. Use a set of pliers to disconnect the wire from the old brush and a flat-head screwdriver to lift the old brush out of its slot. Insert the new brush box assembly into the slot and connect its wires. Finally, reattach the sander outer housing and secure it with the screws.

CORD

$19.10

Fix Number: FIX19516305
Manufacturer Part Number: 3604460555

This cord is a genuine OEM replacement part and is sold individually. Power Cord Specifications: 2 Wires. 18 Gauge. 2 Prongs. 6-1/2 Feet Long. It is constructed with thick insulation for long service life and a strong two-prong plug. This cord is compatible with the tools listed below. It can work for other applications and for other tools as well, but compatibility is not guaranteed. Installation of this part requires the new cord wires be stripped and to fit correctly into the wire terminals.

Popular Orbital or Palm Sander Parts

Installation Instructions

Orbital or Palm Sander Brands

Related Orbital or Palm Sander Parts

Popular Orbital or Palm Sander Models

Orbital or Palm Sander Parts

Start With Your Model Number

Popular Orbital or Palm Sander Parts

Installation Instructions

Orbital or Palm Sander Brands

Related Orbital or Palm Sander Parts

Popular Orbital or Palm Sander Models