Washer Dryer Combo Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Shop By Brand Shop By Part Type

Popular Washer Dryer Combo Parts

Watch the install video
Drum Support Roller Kit – Part Number: 12001541
Drum Support Roller Kit
$20.95
In Stock
★★★★★
★★★★★
10 Reviews
Fix Number
FIX1570070
Manufacturer Part Number
12001541
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Dryer Bearing Slide (2 Pack) – Part Number: WE03X37319
Dryer Bearing Slide (2 Pack)
$15.95
In Stock
Fix Number
FIX17137207
Manufacturer Part Number
WE03X37319
f your dryer is excessively noisy when operating, is not tumbling, or is leaving marks on your laundry, it may be time to replace the drum glides. The drum glide bearing is a genuine OEM part for your dryer and is used to help the drum rotate smoothly and quietly. If the bearing has worn out, it can make your dryer noisy when operating, with a metal-on-metal sound. Please be sure to disconnect the power supply to the dryer before beginning this repair.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...
Watch the install video
Agitator Directional Cogs – Part Number: 80040
Agitator Directional Cogs
$6.44
In Stock
★★★★★
★★★★★
20 Reviews
Fix Number
FIX388034
Manufacturer Part Number
80040
Commonly referred to as dog ears, these agitator directional cogs are manufacturer approved replacement parts that come in a package of 4 and are usually used with direct drive washing machines. We recommend replacing all 4 directional cogs at the same time. The agitator directional cogs reach across the gear teeth in one direction and dig into the gear teeth in the other direction to create the needed agitation. This thrusting motion is what tumbles your clothes during the wash cycle. When the teeth on the outer edge are damaged, the cogs will not engage with the upper agitator, making it impossible to agitate as it should. If your machine makes unusual noises, shakes/moves while operating, or will not spin or drain properly, it may be time to replace them. To access this part, simply remove the softener dispenser and then the agitator cap. You will find them attached to the agitator. Each cog is approximately 1 inch long and made of a durable plastic.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Marks left on clothes
  • Noisy and Marks Left on Clothes
  • See more...

Installation Instructions

John from La Mesa, CA
Upper agitator stopped working
Followed the simple instructions on youtube, searching for "kenmore upper agitator doesn't work." There are a number of videos there. Find the notch on agitator cover and pry off the cover using a flat screw driver. Remove the nut in the center of the agitator using the 7/16 socket with extension. Remove upper agitator (mine came off easily but some may require removing the entire agitator, then pulling off the upper agitator). Remove assembly from inside and replace the dogs. Reassemble. Read more...
Washer Door Boot Seal – Part Number: 5304505004
Washer Door Boot Seal
$89.14
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12731388
Manufacturer Part Number
5304505004
Also known as a door gasket or door bellows, this OEM door boot creates a watertight seal between the inner drum and the outer cabinet of your washing machine. It's a crucial part in preventing leaks during wash cycles. If you notice water or soap leaking from the door, or see signs of wear like tearing or looseness around the drum, it's likely time to replace the boot. Installation requires removing the existing clamp with pliers, and this replacement is sold individually. Please note that any required clamps or securing parts must be purchased separately.
Fixes these symptoms

Installation Instructions

Thomas from BINGHAMTON, NY
Don’t even try it
It’s not hard to remove the bellows but reinstalling is a nightmare. The spring has to be spread so far it is virtually impossible to get on. Installation videos show securing it with clamps, good luck with that. I got it halfway on and it just sprung off allowing my hand to shoot upward into the washer top bracket which by the way is quite sharp on the bottom. Sharp to the extent that it slit the lower knuckle on my right thumb to the bone and now I sit here with a swollen hand and seven stitches. I doubt they will publish this but if they do my recommendation is don’t even try and by the way I am experienced over many years and have never had a problem installing anything except this. Read more...
Dryer Lint Filter – Part Number: ADQ56656401
Dryer Lint Filter
$34.95
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX3531962
Manufacturer Part Number
ADQ56656401
The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.
Fixes these symptoms
  • Clothes Still Wrinkled
  • Door won’t close
  • Marks left on clothes
  • See more...

Installation Instructions

Frank from Eau Claire, WI
Damaged lint dryer and guide, kid didn't push down lint filter and nap sack rope caught it yanked apart assembly.
Removed screws, took a whopping 5 minutes, including unpacking box assembly of screw driver. Grab a vacuum, good time to clean out inside of dryer while torn apart. EZ repair. Read more...
Watch the install video
Idler Pulley – Part Number: 279640
Idler Pulley
$25.88
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX334244
Manufacturer Part Number
279640
Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin. It is located on the dryer drum, around the tension pulley. If your appliance is noisy during operation, will not tumble, or will not start, you may need to replace this part. It is made of durable plastic and has a diameter of roughly 2-inches. This part also includes the hardware needed for replacement. Most of our customers found this repair to be medium difficulty, and required a Philips screwdriver, 1/4-inch nut driver, putty knife, small flat blade screwdriver, and needle nose pliers to get the job done.
Fixes these symptoms

Installation Instructions

David from Mount Carmel, PA
belt , pulley, and pulley bracket
Very easy... I you tubed nd watched the video took the dryer apart, found the problem & ordered the parts they arrived in 2 days and put it together in 45 minutes. Read more...
Watch the install video
Roller Shaft – Part Number: WP6-3129480
Roller Shaft
$9.92
On Order
Fix Number
FIX11743031
Manufacturer Part Number
WP6-3129480
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while operating, or will not tumble at all, you may need to replace the roller shaft. You may also want to inspect the drum rollers at the same time and replace them if necessary. Replacing the roller shaft will require that you remove the front panel and the drum from the dryer. Please ensure that you disconnect the power supply before beginning this project. The tools you will need include a Philips screwdriver, a 5/16-inch nut driver, a pair of snap-ring pliers, and a 9/16-inch wrench. The roller shaft is an authentic OEM part.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...
Watch the install video
Tumbler and Motor Belt – Part Number: WPY312959
Tumbler and Motor Belt
$25.09
In Stock
★★★★★
★★★★★
9 Reviews
Fix Number
FIX11757542
Manufacturer Part Number
WPY312959
This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Watch the install video
Dryer Drum Support Roller – Part Number: WPW10314173
Dryer Drum Support Roller
$18.83
In Stock
Fix Number
FIX11752609
Manufacturer Part Number
WPW10314173
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

JAMES from GREENSBURG, PA
Loud squeaking and squealing
Lint Filter - Removed old lint filter and inserted new lint filter. This is the first time I tried to fix a dryer. A handyman I am not. I found two very useful YouTube videos using basically my model of Kenmore (11067851600). Disassembly/Assembly - here is a difference between Kenmore 29" wide dryers and 27" wide dryers. Mine is 27". My effort was not a smooth as these videos. The bottom front panel's right most clip was quite troublesome. The moisture sensor wire required needle nose pliers to be disconnected and reconnected. The open door sensor was not easy to disconnect. Although with a few special magic words it came apart. The upper front panel was held in place with two T20 Torx screws. I had only had a T15 driver, therefore a trip to Home Depot was required. The first two tri rings were not easily removed, however, on third tri ring it became easier and not damaged. Replacement of tri rings was not troublesome. Support rollers snapped in place easily. However, I did thoroughly clean the housing. It was quite grimy. Actually, while I had the dryer open I cleaned everything including the heating element and electric motor. It now operates quietly. It took me a little over two hours because I am not handy and must take care not to make matters worse plus I thoroughly cleaned everything include scuff marks where the drum rubs. Anyone else probably should have it completed 30-60 minutes easily. Read more...
Watch the install video
Front Glide Kit – Part Number: 306508
Front Glide Kit
$13.58
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX1804752
Manufacturer Part Number
306508
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may need to replace the front glides. This genuine OEM front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. We recommend replacing both sets of glides at the same time, which will require the purchase of two kits. To complete this repair, you will need a Philips screwdriver and a 5/16 nut-driver to remove the front panel and the bulkhead of the dryer, a drill with a 1/8-inch bit to remove the old rivets, and a rivet tool to install the new ones. Please ensure that you disconnect the power supply to your dryer before beginning this repair. While you have the appliance opened, we recommend vacuuming out any lint and debris, and inspecting the felt around the bulkhead and replacing if necessary.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...

Washer Dryer Combo Brands

Related Washer Dryer Combo Parts

Popular Washer Dryer Combo Models

View More
+