Washer Dryer Combo Fuses

★★★★★

★★★★★

16 Reviews

Fix Number

FIX11741460

Manufacturer Part Number

WP3392519

The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX334299

Manufacturer Part Number

279816

This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to prevent further damage. It may need to be replaced if your washer is no longer heating properly. This is a one-time fuse, meaning if it trips, it needs to be replaced immediately. A common reason for this part to fail is if the heater housing is not receiving proper airflow, normally caused by an obstruction in the exhaust vent, a clogged lint screen, or a broken blower wheel. This kit includes 1 high-limit thermostat with a limit of 250 degrees Fahrenheit, 1 thermal cut-off fuse with a limit of 309 degrees Fahrenheit, jumper wires and new female spade terminals. These components are attached to the heater housing.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334278

Manufacturer Part Number

279769

This genuine OEM kit includes a high limit thermostat and a thermal cut-off fuse for your dryer. The thermostat has a limit of 250 degrees Fahrenheit, and the fuse has a limit of 360 degrees Fahrenheit. The purpose of these parts is to prevent your dryer from overheating. If your clothes are coming out of the dryer too hot, or there is no heat at all, it is likely that these parts will need to be replaced. To complete this repair, you will need a putty knife, quarter-inch nut driver, and a pair of pliers. Please be sure to disconnect the power supply to your dryer before beginning this repair. The thermostats are located on the element housing, and we find it easiest to remove the entire heating assembly from the dryer in order to replace these parts. Take note when removing the old thermostats, if there is any discoloration on the terminals then the wire ends may also need to be replaced.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX3530485

Manufacturer Part Number

6931EL3003D

If your dryer is not turning on, or not heating up, there could be an issue with your thermal fuse. This OEM fuse is designed to act as a high-limit thermostat, and will turn off the heating element in your dryer if the appliance overheats. It does this by cutting off power to the dryer. If the fuse has blown, it will need to be replaced as they cannot be reset. You can test the fuse with a multimeter, and should receive a reading of 0 ohms of resistance if the fuse is still good. A common reason for a dryer to overheat is if the air vents are blocked, as the hot air is contained in the dryer causing the fuse to blow. Be sure to keep your dryer filter and vents clean of lint and other debris to prevent this from happening.

Fix Number

FIX419402

Manufacturer Part Number

134120900

This thermal fuse limiter is used in dryers to monitor the temperature and make sure it does not overheat. The thermal fuse has a limit of 220 degrees Fahrenheit before the heating element and power are cut off. If your thermal fuse has blown or is damaged then your dryer will not start, can over heat, or take too long to dry. It is important to replace the fuse to solve the above problems. For this repair, you will need a Philips screwdriver, putty knife, and a needle nose plier. As a safety precaution, remember to unplug dryer from power source to avoid electrocution when installing this part. Refer to the manual provided by the manufacturer for further instructions.

Fix Number

FIX12070444

Manufacturer Part Number

W11050897

This OEM high-limit thermostat kit includes the thermal cut-off fuse and the high-limit thermostat. The purpose of this part is to cut-off power to the dryer when it overheats. Common indications that this part requires replacement are if your dryer will not start, it is overheating, or no heat is coming from the dryer at all. Please note that the manufacturer has made updates to this part so it may look different from the original.

Fix Number

FIX2349395

Manufacturer Part Number

137032600

Fix Number

FIX11741444

Manufacturer Part Number

WP3390719

This part includes a dryer thermal fuse, also sometimes referred to as a thermal limiter, for dryers. This authentically sourced part is located on the exhaust duct and acts a safety mechanism that shuts off the power to the dryer when it overheats. This part can be tested for continuity between the two terminals, and if no continuity is detected, it will need to be replaced. The thermal fuse cannot be reset. Once the fuse opens, it needs to be replaced to get your dryer back up and running again.

Fix Number

FIX4704883

Manufacturer Part Number

134711401

This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are detected, helping prevent damage or potential fire hazards. Once the fuse is triggered, it cannot be reset and must be replaced. A faulty thermal fuse may cause the dryer not to start, run without heat, shut off prematurely, or operate at unsafe temperatures. Replacing this component helps restore safe and proper dryer operation.

Fix Number

FIX11746693

Manufacturer Part Number

WP8573713

The thermal cut off fuse will disrupt the power flow to the drive motor when the dryer gets too hot. If your dryer will not heat properly, or will not heat at all the issue could be with a faulty or damaged thermal cut off fuse. Before you replace the faulty cut off fuse, make sure you disconnect the power from your dryer.