Official Whirlpool Washer Dryer Combo Fuses

Dryer Thermal Fuse

$17.44

Fix Number: FIX11741460
Manufacturer Part Number: WP3392519

The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.

Fixes these symptoms

Drum Not Spinning
Heat stays on after drum has stopped
Not Heating
See more...

Watch the install video

Thermal Cut-Off Kit

$48.21

★★★★★

8 Reviews

Fix Number: FIX334299
Manufacturer Part Number: 279816

This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to prevent further damage. It may need to be replaced if your washer is no longer heating properly. This is a one-time fuse, meaning if it trips, it needs to be replaced immediately. A common reason for this part to fail is if the heater housing is not receiving proper airflow, normally caused by an obstruction in the exhaust vent, a clogged lint screen, or a broken blower wheel. This kit includes 1 high-limit thermostat with a limit of 250 degrees Fahrenheit, 1 thermal cut-off fuse with a limit of 309 degrees Fahrenheit, jumper wires and new female spade terminals. These components are attached to the heater housing.

Fixes these symptoms

Heat stays on after drum has stopped
Not Heating
Too hot
See more...

Watch the install video

Thermal Cut-Off Kit

$36.42

★★★★★

2 Reviews

Fix Number: FIX334278
Manufacturer Part Number: 279769

This genuine OEM kit includes a high limit thermostat and a thermal cut-off fuse for your dryer. The thermostat has a limit of 250 degrees Fahrenheit, and the fuse has a limit of 360 degrees Fahrenheit. The purpose of these parts is to prevent your dryer from overheating. If your clothes are coming out of the dryer too hot, or there is no heat at all, it is likely that these parts will need to be replaced. To complete this repair, you will need a putty knife, quarter-inch nut driver, and a pair of pliers. Please be sure to disconnect the power supply to your dryer before beginning this repair. The thermostats are located on the element housing, and we find it easiest to remove the entire heating assembly from the dryer in order to replace these parts. Take note when removing the old thermostats, if there is any discoloration on the terminals then the wire ends may also need to be replaced.

Fixes these symptoms

Not Heating
Too hot
See more...

Thermal Cut-Off Fuse Kit

$16.35

Fix Number: FIX12070444
Manufacturer Part Number: W11050897

This OEM high-limit thermostat kit includes the thermal cut-off fuse and the high-limit thermostat. The purpose of this part is to cut-off power to the dryer when it overheats. Common indications that this part requires replacement are if your dryer will not start, it is overheating, or no heat is coming from the dryer at all. Please note that the manufacturer has made updates to this part so it may look different from the original.

Fixes these symptoms

Not Heating
Too hot
See more...

Dryer Thermal Cutoff

$55.18

Fix Number: FIX11746693
Manufacturer Part Number: WP8573713

The thermal cut off fuse will disrupt the power flow to the drive motor when the dryer gets too hot. If your dryer will not heat properly, or will not heat at all the issue could be with a faulty or damaged thermal cut off fuse. Before you replace the faulty cut off fuse, make sure you disconnect the power from your dryer.

Fixes these symptoms