KitchenAid Washer Dryer Combo Parts

KitchenAid Appliance Parts
Shop By Appliance Type

Popular KitchenAid Washer Dryer Combo Parts

$20.14
  In Stock
Dryer Thermal Fuse
★★★★★
★★★★★
(13)
Fix Number FIX11741460
Manufacturer Part Number WP3392519
The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
$6.32
  In Stock
Door Catch Kit
★★★★★
★★★★★
(9)
Fix Number FIX334230
Manufacturer Part Number 279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
  • Door won’t close
  • Lid or door won’t close
  • No heat or not enough heat
  • See more...
Installation Instructions
jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third! Read more...
$28.24
  In Stock
M Series New Style Coil Kit
★★★★★
★★★★★
(1)
Fix Number FIX334310
Manufacturer Part Number 279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Shuts off too soon
  • See more...
Installation Instructions
John from Warrington, PA
Dryer did not stay hot
To avoid the mistake I made, make sure you pop the small, square white plug towards the bottom left on the front of the dryer. This gives you a view into the heater so you can see if the igniter and other components are working. In our case, the heater would ignite and stay on for 5 minutes and then go out. As noted on this site, 50% of the time it is the gas coils so we tested them and they tested fine cold. However, testing all of the other electrical components and they tested out as well so we purchased the coil kit (again 50%). Following one of the many videos on the site, it was quite simple to get to the coils. Unplug and turn off the gas at the wall. Unscrew the two screws in the lint trap and pop up the lid with small flat screwdriver as there is a catch on each side under the lip in the front. With the top lid up, pull up and out on the front panel, the drum will stay in place but dip as you remove the front panel holding the drum in place. Reach under and to the right to remove the belt around the drum so you can remove the drum. The coils are right in front and are easily removed with a phillips screwdriver to remove the cap holding the coils. The coils are keyed and just slide out and into place. Replace the cap and reverse the steps. However, while you have the dryer apart, it is a good idea to remove all of the extra lint as we also did the same removing the back panel and the lint trap apparatus. We had quite the collection of lint and stuff in the blower that could never be removed without taking this apart so I highly suggest you take a look. It is about 10 phillips screws holding everything in place. With the coils in place, the dryer starts hot and stays hot. Repaired in under an hour and under $25 thanks to this site! Read more...
$25.51
  In Stock
Direct Drive Motor Coupling
★★★★★
★★★★★
(7)
Fix Number FIX1485646
Manufacturer Part Number 285753A
This is an OEM direct drive motor coupling, which provides a cushioned connection between the transmission and the motor shaft. This is the newer version of this part, made with new metal sleeves for added strength. It is located between the motor and transmission on direct drive washers with no belt. If the drive system seizes, the coupling is designed to break to prevent the drive motor from damage. Consequently, this part may need to be replaced as your appliance ages. Never overload your washer, as this can speed up its deterioration. Symptoms of a faulty motor coupling include a washer pumping but not spinning, slow spinning, the washer not agitating, and unusual noises. This coupling kit contains all the parts necessary to replace your existing direct drive motor coupling. Please note, that after replacing the motor coupling your washer may smell like burning rubber for the first few uses, this is entirely normal as the part becomes acclimated to the machine. Each is sold individually.
Fixes these symptoms
Installation Instructions
Joseph from Burnsville, NC
Washer would not spin or agitate
First, I found it very easy to follow the help on your web site to determine the most likely parts that would cause my problems. The direct drive motor coupling could be the cause of both problems. Also the agitator repair kit was the most likely cause of the agitator problem, So, I ordered both parts. When AI received the parts there were videos included instructing every detail for installation. I just followed the video for the direct drive motor coupling and both problems were solved with the one part. It took about 30 minutes and was a simple installation. .Thanks for your good service. It saved me a service call or maybe a new washer and dryer set. Read more...
$19.44
  In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(3)
Fix Number FIX347627
Manufacturer Part Number 349241T
This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.
Fixes these symptoms
  • Marks left on clothes
  • Noisy
  • Will Not Start
  • See more...
Installation Instructions
Tyrik from KENNESAW, GA
The roller support wheels were worn down and needed replacing.
Step 1: removed power source.
Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back.
Read more...
$46.95
  In Stock
Dryer Lint Filter and Cover
Fix Number FIX11726200
Manufacturer Part Number W10828351
Cover and filter as an assembly. It is used in dryer, If the lint filter cover is damaged or cracked, it should be replaced.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Kathleen from Stuart, NY
Replacement part
Just replaced Read more...
$37.55
  In Stock
Direct Drive Water Pump
Fix Number FIX11741239
Manufacturer Part Number WP3363394
The direct drive water pump is used in washing machines that do not have belts,?to?remove water from the?tub?during the drain cycle. It is located on the motor and attached by two clips. The drain pump has two ports?for water to pass through, one port is larger than the other, and this is where the hoses connect.?If your washer leaks, won?t drain the water, or is filling and draining at the same time, there may be an issue with your pump. Blockages or clogs in the hoses may be contributing to this.?Before you replace the pump, be sure to disconnect the power and water lines to your appliance. This repair requires a pair of slip-joint pliers, a flat head screwdriver, and a putty knife. You may find it useful to have a container on hand?to collect?any water left in the hoses, and to have another person to assist with lifting and lowering the machine. This is a genuine OEM part made of durable white plastic. Other names you may know it by include direct drive washer pump, drain pump, washer drain pump, or water pump.?
Fixes these symptoms
  • Fills and drains at the same time
  • Leaking
  • Leaks water
  • See more...
Installation Instructions
Jerry from Aransas Pass, TX
Agitator not working correctly and leaking from somewhere underneath.
I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future. Read more...
$18.32
  In Stock
Idler Pulley Assembly
★★★★★
★★★★★
(1)
Fix Number FIX11743765
Manufacturer Part Number WP691366
The idler pulley is found in your dryer and provides tension to the belt in order to rotate the drum. If your clothes are taking a long time to dry, the machine is noisy while operating, or the dryer will not start or tumble, there may be an issue with the idler pulley assembly. To replace this part, you will need to lift the top and remove the front panel of the dryer. You will want to take note of how the drum belt is positioned so it can be put back in place once the new idler pulley is in place. While you have the appliance opened up and accessible, you may want to consider replacing the drum belt at this time.
Fixes these symptoms
  • Noisy
  • Takes too long to dry
  • Will Not Start
  • See more...
Installation Instructions
carolyn from phila, PA
not spinning
follow the vidio Read more...
$27.88
  In Stock
Lid Switch
Fix Number FIX11723153
Manufacturer Part Number W10820036
This 3 prong lid switch is used for washing machines that do not have a tub light.
Fixes these symptoms
  • Pumps but will not spin
  • Timer will not advance
  • Will not agitate
  • See more...
Installation Instructions
Lloyd from ESKO, MN
would not complete rinse cycle
Unplug power cord
lift and brace up top of washer. No need to remove whole top.
disconnect the two leads from old switch.
remove and discard metal clip from new switch.
replace new switch assembly with screws.
reconnect leads.
reclose plastic proctecter over new switch
plug in power cord. That's it.
Read more...
$232.18
  In Stock
Gearcase
Fix Number FIX341974
Manufacturer Part Number 3360629
This is used in your direct drive washer that has a neutral drain.
Fixes these symptoms
  • Noisy
  • Pumps but will not spin
  • Will not agitate
  • See more...
Installation Instructions
Paul from Mobile, AL
would not spin
well i replaced a lot of parts..but i think it was the the lid switch. but now its brand new..Thanks Read more...

Appliance Type

Popular KitchenAid Washer Dryer Combo Models