General Electric Washer Dryer Combo Parts

Start With Your Model Number

Find Parts Fast Guaranteed Fit Repair Videos
Need help finding your model number?
General Electric Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular General Electric Washer Dryer Combo Parts

Watch the install video
BELT DRIVE – Part Number: WE03X29897
$36.13
In Stock
BELT DRIVE
★★★★★
★★★★★
1 Review
Fix Number FIX16542496
Manufacturer Part Number WE03X29897
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretching and contortion will occur over time, and this belt will fit despite small inaccuracies. You will find this part wrapped all the way around the dryer drum, around a tension pulley, and around the drive motor pulley. This allows the parts to work together to spin the drum as the motor rotates. A common symptom of a broken drive belt is a drum that will not turn. This part is prone to wear and tear over time and will likely stretch or become brittle, leading to complete breakage of the part. The drum cannot spin without a drive belt, so it needs to be replaced immediately. For this repair, we recommend wearing work gloves to protect your hands from sharp edges, disconnect the power, remove the main panel, and access the motor drive to secure the new belt in place.
Fixes these symptoms
Installation Instructions
Nae from BRENTWOOD, TN
The dry was making a whining sound. Very loud.
I followed all the video on the website with all the parts I had purchased. Very easy. Just make sure you unplug the dryer first. Thank you, Read more...
Watch the install video
BEARING SLIDE – Part Number: WE03X34318
$8.06
In Stock
BEARING SLIDE
Fix Number FIX16762550
Manufacturer Part Number WE03X34318
If your dryer is making a squealing, metal-on-metal noise you may need to replace your slide bearings. These slide bearings are genuine OEM replacement parts that measure approximately 3 inches in length. They act as a supportive liner for the dryer and prevent the scraping or squealing noise from occurring as the drum rotates. If the slide bearings have eroded or become damaged, they should be replaced.
Fixes these symptoms
Drum Glide Bearing - White – Part Number: WE3M51
$13.17
In Stock
Drum Glide Bearing - White
Fix Number FIX4704230
Manufacturer Part Number WE3M51
If your dryer is excessively noisy when operating, is not tumbling, or is leaving marks on your laundry, it may be time to replace the drum glides. The drum glide bearing is a genuine OEM part for your dryer and is used to help the drum rotate smoothly and quietly. If the bearing has worn out, it can make your dryer noisy when operating, with a metal-on-metal sound. Please be sure to disconnect the power supply to the dryer before beginning this repair.
Fixes these symptoms
Push-to-Start Switch – Part Number: WE4M416
$18.20
In Stock
Push-to-Start Switch
Fix Number FIX3487190
Manufacturer Part Number WE4M416
This push-to-start switch is a genuine OEM part and is used to activate your dryer. If your dryer will not start, or will only start if the switch is pushed down, or the timer knob is not engaging with the starter, you may need to replace the switch. The tools you will need to replace this part are a Phillips screwdriver and a flat blade screwdriver. Please be sure to disconnect the power supply to your dryer before beginning this repair.
Fixes these symptoms
  • Touchpad does not respond
  • Will Not Start
  • Won’t Start
  • See more...
Installation Instructions
William from MARYVILLE, TN
My dryer would not start
Step 1. After unplugging the dryer from the wall outlet, Removed 6 screws holding the back cover of the instrument panel.
Step 2. Removed the start switch by gently twisting left and pulling out of the socket.
Step 3. Removed the three wires, one at a time and placed them on the new start switch, then installed the new switch in its socket by gently twisting to the right.
(Note: plugged power cord back in and tried the new Start Switch. Still would not start.)
Step 4. Removed the Timer Knob by pulling strait off the shaft, then replaced with the new knob. Pushed the Start button and the Dryer worked. The old knob was obviously stripped so as to slip on the Timer shaft, giving the impression it was moving but it was not. Read more...
Watch the install video
Drum Bearing Slide - White (Sold individually) – Part Number: WE1M504
$18.58
In Stock
Drum Bearing Slide - White (Sold individually)
★★★★★
★★★★★
1 Review
Fix Number FIX755842
Manufacturer Part Number WE1M504
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the drum as it rotates. They are approximately 3-inches long, 1 inch wide and made from a durable white plastic. If your appliance starts making unusual sounds, is not drying clothes properly, or leaves marks on clothes, it may be time to replace this part. The dryer has 2 slides, which we recommend replacing at the same time, as they tend to wear out at the same rate. You will need to order 2 of this part to replace both drum bearing slides, since it is sold individually. Before you begin this repair, be sure to disconnect the power to the dryer.
Fixes these symptoms
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
HANDLE SOLID DOOR – Part Number: WE01X30378
$70.91
In Stock
HANDLE SOLID DOOR
★★★★★
★★★★★
2 Reviews
Fix Number FIX12743305
Manufacturer Part Number WE01X30378
Fixes these symptoms
Watch the install video
Drum Bearing Slide - Green (Sold individually) – Part Number: WE1M1067
$14.29
In Stock
Drum Bearing Slide - Green (Sold individually)
★★★★★
★★★★★
2 Reviews
Fix Number FIX6447706
Manufacturer Part Number WE1M1067
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.
Fixes these symptoms
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Watch the install video
FELT TRAP DUCT – Part Number: WE09X27634
$11.56
In Stock
FELT TRAP DUCT
Fix Number FIX12722961
Manufacturer Part Number WE09X27634
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.
Fixes these symptoms
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
Lid Lock & Switch Assembly – Part Number: WH44X10288
$105.10
In Stock
Lid Lock & Switch Assembly
Fix Number FIX3496878
Manufacturer Part Number WH44X10288
The door latch lid lock is to lock the door on your washer when the appliance is in use. Your washer will not start if your door is not locked. If your latch is broken, you may not be able to start a cycle or open your washer door. It is mostly black in color and made of plastic. This part measures approximately 3.75 by 3.5 inches.
Fixes these symptoms
Watch the install video
Front Drum Bearing – Part Number: WE3M26
$34.14
In Stock
Front Drum Bearing
★★★★★
★★★★★
2 Reviews
Fix Number FIX960316
Manufacturer Part Number WE3M26
Located on the inside of the dryer front panel, the front drum bearing helps your appliance to operate as quietly as possible. It allows the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. This manufacturer-approved part is made of a durable white plastic and measures approximately 9 inches by 20 inches. If your dryer makes a continuous banging noise while it is powered on, it is likely that the drum bearings need to be replaced. Keep in mind that the drum slides should be replaced at the same and will need to be purchased separately (the front drum bearing holds 4 glides), as this part includes the bearing only.
Fixes these symptoms
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...

Appliance Type

Related Pages

Popular General Electric Washer Dryer Combo Models

View More
+