Models > WSM2700DAWWW

WSM2700DAWWW General Electric Washer Dryer Combo

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for WSM2700DAWWW

Viewing 6 of 6
CONTROL PANEL
DRYER MOTOR, BLOWER & BELT
DRYER UPPER CABINET, DRUM & HEATER
TRANSMISSION
WASHER LOWER CABINET & TOP
WASHER MOTOR & TUB

Manuals & Guides for WSM2700DAWWW

Click to download
Install
Installation Instructions
(0.55MB)
Manual
Owner's Manuals
(2.18MB)
Keep searches simple, eg. "belt" or "pump".
DRYER LINT FILTER – Part Number: WE16X29397
$117.10
This is the replacement lint filter for your dryer. The lint filter traps unwanted lint and debris so your dryer can effectively dry your clothes.
In Stock
Timer Knob - Dryer – Part Number: WE01X10160
$71.90
Used with washer/dryer combo machines. This knob takes a D-shaped shaft.
In Stock
Drum Belt – Part Number: WE12X10009
$74.86
Used to turn the drum.
In Stock
Drum Glide – Part Number: WE03X10007
$67.07
Sold individually. There are some dryers that require 2 per dryer. They attach to the outer-most sides of the bearing.
In Stock
Rear Bearing Shaft Support – Part Number: WE13X10011
$103.09
In Stock
Upper Felt Seal with Adhesive – Part Number: WE09X10013
$98.05
On Order
DRYER BEARING BRACKET – Part Number: WE13X28680
$32.27
This bracket is used on the drum bearing.
In Stock
Drain Pump – Part Number: WH23X10041
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
V-Belt – Part Number: WH07X10009
$80.60
In Stock
Lower Felt Seal with Adhesive – Part Number: WE09X10014
$104.30
In Stock
Agitator Drive Hub – Part Number: WH40X175
No Longer Available
High Limit Safety Thermostat – Part Number: WE4X757
$66.35
This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees...
In Stock
Back to Top View More
Questions and Answers

Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top

Common Problems and Symptoms for WSM2700DAWWW

Viewing 9 of 9
Noisy
Fixed by these parts
How to fix it
Will not tumble
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Timer will not advance
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Takes too long to dry
Fixed by these parts
How to fix it
No heat or not enough heat
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Back to Top
Replacing the Drum Belt play video

Replacing the Drum Belt

Back to Top View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Jack from Canyon Lake, TX
  • Parts Used:
    WH23X10041
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Washer would not drain
Removed 2 Hose clamps with pliers. Unplug power source from drain pump. Unscrew 2 mounting screws with 5/16" nut-driver then replace unit in reverse sequence...... Very simple.
25 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Patricia from chicago, IL
  • Parts Used:
    WE16X29397
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
filter had a hole
simple replacement
14 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Dave from Salt Lake City, UT
  • Parts Used:
    WE01X10160
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Control knob had broken and we were unable to set the dryer
I first ordered the replacement knob. It had broken before and I had repaired using a steel washer and epoxy to support the cracked plastic. When the support system I installed broke, I suspected a deeper problem; increased resistance to knob rotation in the control system. I removed the front panel to get back at the switch area. I wanted to lubricate the whole control, but UT seemed to be well sealed. Finding a couple areas where the plastic came together, held by a permanent metal mount, I used a pressurized silicone lubricant and sprayed into the small spaces. That allowed for easier rotation of the control, hopefully giving a longer lifespan to the new knob. DO
10 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Back to Top View More