Jenn-Air Washer Dryer Combo Parts

★★★★★

★★★★★

10 Reviews

Fix Number

FIX1570070

Manufacturer Part Number

12001541

This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).

★★★★★

★★★★★

9 Reviews

Fix Number

FIX11757542

Manufacturer Part Number

WPY312959

This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX1804752

Manufacturer Part Number

306508

This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may need to replace the front glides. This genuine OEM front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. We recommend replacing both sets of glides at the same time, which will require the purchase of two kits. To complete this repair, you will need a Philips screwdriver and a 5/16 nut-driver to remove the front panel and the bulkhead of the dryer, a drill with a 1/8-inch bit to remove the old rivets, and a rivet tool to install the new ones. Please ensure that you disconnect the power supply to your dryer before beginning this repair. While you have the appliance opened, we recommend vacuuming out any lint and debris, and inspecting the felt around the bulkhead and replacing if necessary.

★★★★★

★★★★★

5 Reviews

Fix Number

FIX2200270

Manufacturer Part Number

Y303836

The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.

★★★★★

★★★★★

1 Review

Fix Number

FIX2005284

Manufacturer Part Number

12112425

Over time, the belts in your washer can either stretch out and sag, or become brittle and snap. When this happens, it can result in the belt losing its grip and will not be able to spin or drain the tub. If this happens, the belts will need to be replaced. This OEM belt kit includes the drive belt and the pump belt, which are both V-shaped, and made of black rubber. The pump belt is located between the motor and pump under the washer, and the drive belt is looped around the drive and motor pulley at the bottom of the machine. This repair is easiest to complete if the washer is placed on its back, and you will need to disconnect the power and water supply.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX11741039

Manufacturer Part Number

WP33001003

This lint filter is a genuine OEM replacement part for your dryer. The lint filter is used to trap debris and prevent it from clogging up your dryer vents. If your lint filter has become damaged it should be replaced. Using your dryer without a lint filter can be a serious fire hazard, along with decreasing the efficiency of the machine. No tools are required to replace this part, simply pull out the old filter and slide the new one into place.

Fix Number

FIX11743028

Manufacturer Part Number

WP6-3037050

This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.

★★★★★

★★★★★

1 Review

Fix Number

FIX11757538

Manufacturer Part Number

WPY312527

This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.

Fix Number

FIX11740771

Manufacturer Part Number

WP314820

This front or rear dryer drum felt seal is seventy-nine and a half inches long.

Fix Number

FIX11740748

Manufacturer Part Number

WP312535

This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.