Front or Rear Drum Felt Seal WP314820
$28.92
In Stock
- Fix Number:
- FIX11740771
- Manufacturer #:
- WP314820
- Manufactured by:
- Whirlpool
Jump to:
Product Description
This front or rear dryer drum felt seal is seventy-nine and a half inches long.
-
Works with the following brands:Maytag, Jenn-Air, International
-
Works with the following products:Dryer, Washer Dryer Combo
-
Fixes the following symptoms:Noisy, Marks left on clothes
-
Part# WP314820 replaces these:AP6007654, 3-14820, 314820
- Works with the following brands:
- Maytag, Jenn-Air, International
- Works with the following products
- Dryer, Washer Dryer Combo
- Fixes the following symptoms
- Noisy, Marks left on clothes
- Part# WP314820 replaces these:
- AP6007654, 3-14820, 314820
Part Number Cross Reference
Videos For installing this part.
Replacing your Front or Rear Drum Felt Seal
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts Additional or alternate parts to consider.
View More
View Less
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer makes horrible noise but drum still turns.
The old dilemma is whether to fix a >20y/o dryer, or just buy a new one. With minimal effort, it was easy to find the source of the noise by manually turning the drum. Noise in the front turned out to be the blower wheel which is located right in the front of the dryer. Removing about 6 screws shows the motor shaft wore out the plastic ce
... Read more
nter of the blower wheel and so the blower wheel was not spinning properly and bouncing around in the housing. Typing in the Model # in PartSelect.com gave me the whole diagram and exactly what to order. Since I had the dryer apart anyway, I decided to go ahead and replace the felt seals and drum/motor belt and front glides. Easy instructions to do all of this is available on multiple YouTube videos. The only caveat is some of these items are held in w/ snap rings. It's possible to deal with snap rings using a small screwdriver and pliers but having special snap ring pliers makes this step a whole lot easier. In my case the drum support rollers and belt tensioner roller turned out to be fine and only needed some lubrication. Also, in this particular model, the felt seals are held on w/ sheet metal tabs and do not require the expensive heat resistant glue. All parts installed, dryer back together and works perfectly on the very first try! Saved me a ton of money and the wife is happy, thanks to this site!
Read less
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud squeaking
Unplug power cord. Remove front of dryer (2 Phillips head screws on lower corners). Tilt out by pulling on bottom of front panel to disengage the top. Unplug wiring and set panel aside. Remove 4 screws from shroud (2 on each side) with 5/16 nut driver. Unplug wiring and set aside. Pull out drum. Replace rollers. Remove felt by pulling out
... Read more
of tabs. Use straight screwdriver to pry out tabs a little to install new felt. Work way around with felt pressing down on tabs to hold felt. Do the same on shroud. Tak note of how belt is routed on tensioner and pulley. Remove belt.Put drum back in place. Put belt around drum flat side towards drum. Reach under and install belt on tensioner and pulley. Reinstall shroud. Reinstall front. Job complete
Read less
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy @ front. Wobbly upon inspection.
Thanks to the website I first looked at parts schematics, then a short video on repair. I ordered the parts I thought I needed and repair was easily done. With front cover off, further inspection was done to foresee any future repairs.
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX11740771
Manufacturer Part Number: WP314820
Manufacturer Part Number: WP314820
Brand
Model Number
Description
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.